background image

 

- 3 - 

 

Beam Angle:       

                          Stepless manual zoom from 10

°

to 50

°

 

 

IP rating:

                                          IP20 

 

LED Sources:                               

200W White COB LED 

 

CRI/R9:                                         

  CRI>95;R9>90

 

 

Color Temperature:                   

3200K 

 

Product Dimension:                   

498x265x265mm 

 

Weight(N.W)

                             

4.0 Kgs 

 

3. Checking Parts 

 
Please check if the following parts are included: 
1pc x 200W par 64   
1pc x Power cable 
1pc x User manual 

 

4. Installation and Connection 

 
The unit should be mounted via  its screw holes on the bracket. Always ensure that 

the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure 
that the structure to which you are attaching the unit is secure and is able to support a 
weight of 10 times of the unit

’s weight. Also always use a safety cable that can hold 

12 times of the weight of the unit when installing the fixture. 

 
The equipment must be fixed by professionals. And it must be fixed at a place where 

is out of the touch of people and has no one pass by or under it. The unit should be 
mounted in the height of 0 to 30m. 

 

5. How to set the unit 

 

Rear Panel 

 

 

Summary of Contents for PAR LED COB WW








Reviews: