3-Year Limited Warranty
ecobee warrants that for a period of three (3) years from the date of purchase by the consumer (“Customer”),
the ecobee Power Extender Kit (the“Product”) shall be free of defects in materials and workmanship under
normal use and service. During the warranty period, ecobee shall, at its option, repair or replace any defective
products, at no charge. Any replacement and/or repaired device are warranted for the remainder of the
original warranty or ninety (90) days, whichever is longer.
If the product is defective, contact the supplier from whom the product was purchased to obtain an
equivalent replacement product, provided the supplier determines that the returned Product is defective and
the Customer is otherwise eligible to receive a replacement product;
This warranty does not cover removal or reinstallation costs and shall not apply if the damages were found to
be caused by something other than defects in materials or workmanship, including without limitation, if the
product:
• was operated/stored in abnormal use or maintenance conditions;
• is repaired, modified or altered, unless ecobee expressly authorizes such repair, modification or
alteration in writing;
• was subject to abuse, neglect, electrical fault, improper handling, accident or acts of nature;
• was installed improperly.
ecobee’s sole responsibility shall be to repair or replace the Product within the terms stated above. ECOBEE
SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY,
EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some US states and Canadian provinces
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. ecobee’s responsibility for malfunctions and defects in materials and
workmanship is limited to repair and replacement as set forth in this warranty statement. All express and
implied warranties for the product, including but not limited to any implied warranties and conditions of
merchantability and fitness for a particular purpose, are limited to the three-year duration of this limited
warranty. No warranties, whether express or implied, will apply after the limited warranty period has expired.
Some US states and Canadian provinces do not allow limitations on how long an implied warranty lasts, so
this limitation may not apply. ecobee neither assumes responsibility for nor authorizes any other person
purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty
or liability concerning this product. This warranty gives you specific rights, and you may also have other rights
which vary from jurisdiction to jurisdiction. If you have any questions regarding this warranty, please write
ecobee Customer Service, 477 Richmond St West 2nd Floor, Toronto ON M5V 3E7, Canada or contact customer
service at 1-877-932-6233 or email at support@ecobee.com.
EB-PEK-01
ecobee® is a registered trade-mark of ecobee, inc. © 2013 ecobee, inc. All rights reserved.
Product Specifications
Environmental
For indoor use only
Temperature: -40°F to 160°F (-40°C to 70°C)
Humidity: 5-95% RH (non-condensing)
Dimensions
3.3 x 2.0 x 1.0 inches (84 x 52 x 26 mm)
Electrical
Input: 18 to 30 VAC (50 or 60 Hz), 30mA@24V
Output: 18 to 30 VAC (50 or 60 Hz) 2A per terminal
Need Help?
Contact us at:
Toll free 1.877.932.6233
support@ecobee.com
www.ecobee.com
477 Richmond Street West | 2nd Floor.
Toronto, Ontario , Canada M5V 3E7
Step 3. Connect the Wires
The next step is to connect the wires between the thermostat, diode, wiring
harness, and HVAC equipment.
1. Connect the C wire coming from the thermostat to the C terminal on the
STAT side of the wiring harness. You can repurpose the wire that would
have been connected to W on a 4-wire thermostat.
2. Connect the RC/RH and G wires from the thermostat to the RC/RH and G
terminals on the STAT side of the wiring harness.
3. Connect the output from the diode to the Y terminal on the STAT side
of the wiring harness. You can re-use the wire that would have been
connected to Y on a 4-wire thermostat.
4. Connect the RC/RH, G (fan), Y, C, and W wires on the EQUIP side of the
wiring harness to the matching terminals on your air hander.
Y N/C
W
O/B
G
RC
RH
C
Y2
W2
AUX
Air Handler
W
Y
Diode
Existing 4 wires
(in wall)
G
C
W
Y
RH RC
G
C
W
Y
RH RC
ST
AT
EQUI
P
Thermostat Backplate
Wiring Harness
G
C
W
Y
R
New wire
RC, RH, G (fan), Y & W
connect as usual.
C is a new wire that needs
to be added since there
is no common wire.
RC, RH, & G (fan) connect
as usual
Y is the only wire used for Y & W
C is the repurposed wire
(wire taken from W)
Diode connects to Y & W
Diode output connects
to Y on wiring harness
C (existing wire
taken from W)
Terminals
for 5-wire
thermostat
Step 4. Power On the System
After you have completed the wiring, you can power on and test the system.
1. Re-attach the thermostat to the backplate. Ensure that the pins on the
thermostat align with the terminal block on the backplate.
2. Power on the HVAC equipment. The thermostat should automatically
power on.
3. Test your wiring by alternately adjusting the set temperature and running
the different heat, cool, and fan modes.
4. Once you are satisfied the wiring is correct, re-attach the wiring harness’s
front cover. Make sure the wires exit the module via the wire channel.
5. Re-attach any cover panels that you previously removed on the HVAC
equipment
