417101438_EMPII_E60.docx
- 19 -
Rev. 11-02.14
8
Aufrüstung der EMP II E60 auf EMP II E60
PLUS
Um die
EMP II E60 auf EMP II E60
PLUS
zu erweitern und somit entsprechende Zusatz-
funktionen nutzen zu können sind die Erweiterungseinheiten
Dongle- Box
bzw.
MicroFlow
PLUS
erforderlich.
Die
Dongle- Box
bietet eine Steckplatzerweiterung und zusätzlich die Möglichkeit einen
Ovalradzähler zur Dosiermengenmessung anzuschließen. Ist die Dongle- Box montiert und
durch Aus- und wieder Einschalten der Pumpe aktiviert, so erscheint im Display der Pumpe
links unten die Anzeige „E60+“. Wenn an der
Dongle- Box
an Steckplatz V ein
OGM
PLUS
(Ovalradzähler) angeschlossen und durch Aus- und wieder Einschalten der Pumpe aktiviert
wird, so erscheint im Display der Pumpe die Anzeige „E60++“ und im Pumpenmenü wird
unter Konfiguration automatisch die Funktion Ovalradzähler freigegeben.
Mit dem
MicroFlow
PLUS
ist neben der Steckplatzerweiterung die Auswertung eines speziellen
Durchflussüberwachungssensors auf Basis der konduktiven Leitfähigkeitsmessung möglich.
Bei Anschuss der
MicroFlow- Box
und Aktivierung durch Aus- und wieder Einschalten der
Pumpe wird im Display links unten „E60+microflow“ angezeigt und im Pumpenmenü wird
unter Konfiguration automatisch die Funktion MicroFlow mit dem entsprechenden Untermenü
freigeschaltet.
Hat die Pumpensoftware eine angeschlossene
Dongle- Box
, einen
OGM
PLUS
oder eine
MicroFlow- Box
einmal erkannt und die Kommunikation zwischen Pumpe und Peripherie-
Einheit wird danach unterbrochen (z. B. durch Entfernen der Einheit), so wird eine Fehler-
meldung angezeigt (siehe Kapitel
„Alarmmeldungen (Display)“).
Um zu vermeiden, dass diese Fehlermeldung immer wieder erscheint, muss die
Kommunikation (Verbindung) wieder hergestellt oder die Auswertung in der Pumpensoftware
deaktiviert werden (siehe Kapitel
Dongle Box
,
OGM
PLUS
,
MicroFlow
PLUS
in der Pumpensoftware“).
Äußerlich sind
Dongle- Box
und
MicroFlow- Box
nur durch einen Aufkleber mit der jeweiligen
Artikelnummer zu unterscheiden (
Dongle- Box
Art. Nr. 248606, EBS Nr. 10016094,
MicroFlow- Box
Art.Nr. 248611, EBS Nr. auf Anfrage)
8.1
Montage von Dongle- Box bzw. MicroFlow- Box
Pos.
Bezeichnung
V
Eingang für Ovalradzähler bzw. MicroFlow- Messwertaufnehmer
VI
Festes Verbindungskabel für den Anschluss des Impulseinganges an der
EMP Pumpe (Eingang II)
1
Verbindungsleitung zum Anschluss an Eingang II der Pumpe
2
Dongle-Box bzw. MicroFlow- Box
VII
Eingang für Chargenimpuls oder Dosiersperre
VIII
Eingang für Impuls, Normsignal oder Dosiersperre
Abb. 8.1 Montage von Dongle-Box bzw. MicroFlow-Box
Abb. 8.2 Montage von Dongle-Box bzw. Micro-Flow-Box 1
Abb. 8.3 Montage von Dongle-Box bzw. Micro-Flow-Box 2