- 1 -
- 3 -
- 2 -
- 4 -
WARNING:
Please read this entire manual before installation.
Verify the following contents:
AVERTISSEMENT :
Veuillez lire ce mode d'emploi du début à la fin avant
de commencer l'installation. Vérifiez le contenu suivant :
ADVERTENCIA:
Por favor, lea este manual completo antes de realizar la
instalación. Verifique el siguiente contenido:
Model/Modèle/Modelo #:
SE1038-TBZ-01LF0-E
DUSK-TO-DAWN LED SECURITY LIGHT
(Page 1)
ÉCLAIRAGE DE SÉCURITÉ À DEL FONCTIONNANT
DU CRÉPUSCULE À L'AUBE
(Page 4)
LUZ LED DE SEGURIDAD DE ANOCHECER
A AMANECER
(Página 7)
To Begin/Pour commencer/Para comenzar
Required/Nécessaire/Se necesita
Safety glasses
Lunettes de sécurité
Gafas de seguridad
Flathead screwdriver
Tournevis à tête plate
Destornillador de cabeza plana
Phillips screwdriver
Tournevis cruciforme
Destornillador Phillips
Installation time: 45 minutes
Temps d’installation : 45 minutes
Tiempo de instalación: 45 minutos
Drill bits 1/16 in.
Forets de 1/16 po
Brocas para taladro de 1/16 pulg
Electrical tape
Ruban isolant
Cinta aislante
Drill
Perceuse
Taladro
Pliers
Pinces
Pinzas
Wire cutters
Coupe-fil
Pinzas cortacables
Wire strippers
Pinces à dénuder
Pinzas pelacables
GND
FRONT
Silicone
Silicone
Silicona
Hardware kit (Actual hardware may differ from illustration).
Trousse de quincaillerie (La quincaillerie incluse peut être différente de l’illustration.)
Kit de aditamentos (Los aditamentos reales pueden diferir de los que se muestran en la ilustración.)
Wall plate
Plaque murale
Pared plana
Dusk-to-Dawn sensor
Capteur crépusculaire
Sensor anochecer-amanecer
Light head
Tête de lampe
Cabeza de luz
Diffuser
Diffuseur
Difusor
English
Warnings and Cautions
WARNING
• Shut off power at the circuit breaker or fuse panel before removing the
old fixture or installing the new one.
• LEDs can be damaged by electrostatic discharge (ESD) shock. Before
installation, discharge yourself by touching a grounded bare metal
surface to remove this hazard. To avoid damage, do not remove the
clear lens over the LED module.
CAUTION
•
DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT.
If dimmer
controls are present, remove them and replace them with regular
electrical switches. If a three-way dimmer is present, replace it with a
regular three-way switch. If unfamiliar with electrical installations, it is
recommended a qualified electrician do the installation.
• This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Installation For Round Surface Mount Electrical Boxes
Disconnect power to the electrical box and remove the old fixture. If more than two
wire leads are present, keep track of which wires were connected together.
Pull the supply wires out of the electrical box. Using the
machine screws that fit the electrical box, secure the
mounting strap to the electrical box, making sure that
the side marked “FRONT” is facing out (
Fig. 1
).
1
Fig. 1
Remove the protective paper barrier from the adhesive
face of the foam gasket. Trace the supply wires through
the openings in the gasket and adhere the gasket to the
mounting strap and outer edge of the round surface
mount electrical box (
Fig. 2
).
2
Fig. 2
GND
FRONT
3
For safety and proper installation, the fixture must be
properly grounded. If unfamiliar with the methods of
properly grounding the fixture, consult with a qualified
electrician. A green copper ground wire is
pre-attached to the fixture. If the electrical box is made
of plastic and/or has a green or bare copper grounding
wire inside, the fixture grounding wire and the
electrical box ground wire should be connected together using the wire nut. If the
electrical box is made of metal and already grounded, secure the bare end of the
fixture ground wire to the mounting strap marked “GND” using the green grounding
screw. Push-in connectors are pre-installed onto the fixture’s wire leads to allow for
easy connection. Insert the black lead from the electrical box into the black wire
push-in connector (
Fig. 3
). Repeat with the white leads. Push the excess wires back
into the electrical box.
Fig. 3
GN
D
FRON
T
Position the wall plate over the mounting strap so the
center hole of the wall plate aligns with the center hole
in the mounting strap. While holding the wall plate in
place, put the long machine screw through the center
hole of the wall plate and mounting strap. Tighten the
screw properly to secure the wall plate onto the
electrical box (
Fig. 5
).
NOTE
: Make sure the gasket
properly seals the gap between the wall plate and the electrical box to prevent water
seepage into the electrical box.
5
Fig. 5
4
If eave mounting the fixture, the Dusk-to-Dawn sensor
must be facing outwards (
Fig. 6
).
6
Fig. 6
If the light head is loose and will not hold its position
tighten the screws located on the backside of the light
head that surround the pivot joint (
Fig. 4
).
NOTE
: Tighten
the screws before securing the fixture to the electrical
box.
Fig. 4
Important Safety Instructions
WARNING
: To reduce the risk of FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS:
1. Do NOT touch LEDs.
2. Do NOT remove the protective clear LED lens.
3. Do NOT look directly at lighted LEDs for any length of time.
4. Do NOT touch, operate, or install fixture while in contact with water.
5. For electrical requirements, see back of the fixture. Minimum 90° supply
conductors.
6. Do not leave bare wires exposed outside the wall canopy enclosure.
7. Suitable for installation onto round surface mount electrical boxes or
recessed electrical boxes rated for wet locations. Fixture can be wall or
eave mounted. NOT suitable for ground mount installations.
8. Do NOT mount below 5 ft.
SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO THE FIXTURE TO
REFER TO THEM AT A LATER TIME.
Select the installation location carefully. Do NOT install near other sources
of light, as this can fool the Dusk-to-Dawn sensor into thinking it is daylight.
7
Restore power to the electrical box at the circuit
breaker or fuse panel. Make sure the wall switch that
controls the electrical box for your security light is
returned to the “ON”position and check that your light is
functioning properly. If the light is functioning properly,
fit the silicone cap into the mounting screw opening to
prevent water seepage into the housing (
Fig. 7
).
Fig. 7
Fig. 4
Position the wall plate over the mounting strap so
the center hole of the wall plate aligns with the center
hole in the mounting strap. While holding the wall plate
place the long machine screw through the center
hole of the wall plate and mounting strap. Tighten
the screw properly to secure the wall plate onto the
mounting surface (
Fig. 4
).
3
4
Restore power to the electrical box at the circuit
breaker or fuse panel. Make sure the wall switch that
controls the electrical box for your security light is
returned to the “ON” position and check that your light
is functioning properly. If the light is functioning
properly, use silicone adhesive caulking (not included)
to caulk the gap between the wall plate and the
mounting surface to prevent water seepage into the electrical enclosure (
Fig. 6
).
Fit the silicone cap into the mounting screw
opening to prevent water seepage into the
housing (
Fig. 7
).
6
7
Fig. 7
Fig. 6
Operating Instructions
Installation For Recessed Electrical Boxes
If eave mounting the fixture, the Dusk-to-Dawn sensor
must be facing outwards (
Fig. 5
).
5
Fig. 5
The fixture comes with a built in Dusk-to-Dawn sensor. If the
security light cycles ON and OFF, the Dusk-to-Dawn sensor may
be activating due to reflected light from a nearby surface. Place
the sensor hood firmly over the Dusk-to-Dawn sensor (
Fig. 1
).
This should prevent extraneous light from “tripping” the
Dusk-to-Dawn sensor.
1
To disable the Dusk-to-Dawn sensor, install the sensor cap over
the Dusk-to-Dawn sensor (
Fig. 2
). This will prevent the
Dusk-to-Dawn sensor from controlling the ON/OFF function and
should allow control from the wall switch.
2
Fig. 1
Fig. 2
If the light head is loose and will not hold its position
tighten the screws located on the backside of the light
head that surround the pivot joint (
Fig. 3
).
NOTE
: Tighten
the screws before securing the fixture to the electrical
box.
Fig. 3
Keep this guide handy for
ordering replacement parts.
Hardware Kit
ZH-SE1038F01-TBZ
IMPORTANT
: This light fixture uses light emitting diodes (LEDs) to provide
light. LEDs do not have a filament to burn out like a traditional light bulb.
LEDs gradually emit less light over their lifetime, but will typically last 50,000
hours in a residential environment.
Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner
and soft cloth. When cleaning the fixture, make sure the power is turned off.
Do not spray cleaner directly onto any part of the fixture or LEDs.
In the event you are missing a part or have questions regarding installation
please visit our website at
www.goodearthlighting.com/support
or
call the Customer Care Center
1-800-291-8838
,
8:30 a.m.-5 p.m., CST, Monday-Friday.
Need Help?
Replacement Parts List
Care and Maintenance
6 YEAR LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and
workmanship for a period of (6) years from the date of original purchase by the consumer.
The fixture is not warrantied for use in a commercial or retail application. The warranty is
limited to use in a residential environment. We will repair or replace (at our option) the
unit in the original color, and style if available, or in a similar color and style if the original
item has been discontinued, without charge. Defective units must be properly packed and
returned to the manufacturer with a letter of explanation and your original purchase
receipt showing date of purchase. Call
1-800-291-8838
to obtain a Return Authorization
Number and an address where to ship your defective product. Note: C.O.D. shipments will
NOT be accepted. The liability of the manufacturer is in any case limited to replacement
of the defective light fixture product. The manufacturer will not be liable for any other
loss, damage, labor costs or injury which is caused by the product. This limitation upon
the liability of the manufacturer includes any loss, damage, or injury which is (I) to person
or property or otherwise; (II) incidental or consequential in nature; (III) based upon
theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV)
directly, or indirectly related to the sale, use, or repair of the product. This warranty gives
you specific rights, and you may also have other rights which vary from state to state.
Ecolight ®
is a registered trademark of Good Earth Lighting, Inc. All rights Reserved.
Printed in China
Ecolight®
1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
Warranty
Minor problems often can be fixed without the help of an electrician. Before doing any work
on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
n
o
it
u
l
o
S
e
s
u
a
C
m
e
l
b
o
r
P
Fixture doesn’t light.
Power is off.
Check if power supply is on.
Bad connection.
Check cords and/or wiring.
Bad switch.
Test or replace switch.
Fuse blows or circuit breaker
Discontinue use.
Call customer service.
trips when light is turned on.
Troubleshooting Guide
Disconnect power to the electrical box and remove the old fixture. If more than two
wire leads are present, keep track of which wires were connected together.
Pull the supply wires out of the electrical box. Using the
machine screws that fit the electrical box, secure the
mounting strap to the electrical box, making sure that
the side marked “FRONT” is facing out (
Fig. 1
).
1
Fig. 1
2
For safety and proper installation, the fixture must be
properly grounded. If unfamiliar with the methods of
properly grounding the fixture, consult with a qualified
electrician. A green copper ground wire is
pre-attached to the fixture. If the electrical box is made
of plastic and/or has a green or bare copper grounding
wire inside, the fixture grounding wire and the
electrical box ground wire should be connected together using the wire nut. If the
electrical box is made of metal and already grounded, secure the bare end of the
fixture ground wire to the mounting strap marked “GND” using the green grounding
screw. Push-in connectors are pre-installed onto the fixture’s wire leads to allow for
easy connection. Insert the black lead from the electrical box into the black wire
push-in connector (
Fig. 2
). Repeat with the white leads. Push the excess wires back
into the electrical box.
Fig. 2
