Datum // date
30.03.2017
Teile-Nr. // part no.
300030
Dokument-Nr. Revision //
document no. revision
300030AL06E
04
Software Manual
Ident-Ex
01
Seite/gesamt // page/total
3 / 60
Dokument erstellt // document created
OSJ398 30.03.2017
Dokument geprüft // document checked
FIH091 30.03.2017
Id
en
t-
Ex
01
:
S
of
twar
e
M
a
nual
●
A
b
lag
e
o
rt:
W:
\3
0
0
0
3
0
\0
7
0
_
M
a
rke
tin
g
u
n
te
rlag
e
n
\0
7
0
2
0
_
B
e
d
ien
u
n
g
sa
n
leit
u
n
g
e
n
\3
0
0
0
3
0
A
L
0
6
A
xx
\3
0
0
0
3
0
A
L
0
6
E
0
4
_
Id
e
n
tE
x_
S
o
ft
wa
re
.
d
o
cx
●
te
m
p
lat
e
n
o
.:
0
7
3
0
QV
0
6
A
03
●
te
m
p
lat
e
c
re
a
te
d
:
HA
O0
0
6
2
0
.0
1
.2
0
1
1
●
te
m
p
lat
e
ch
e
cke
d
:
B
E
A
3
7
3
2
0
.0
1
.2
0
1
1
●
loca
tio
n
:
IS
O
d
rive
●
1 Overview
This Software Manual will show all information’s and handling of the Ident-Ex and the “Ident-Ex Setup”
software for Android and Windows.
2 Displaying firmware information
If the main trigger
(trigger button on the underside), trigger (trigger button on the top) and SPP buttons are
pressed during operation, firmware information will be sent to a device that has been connected to the Ident-
Ex via Bluetooth (HID), where it is displayed. It must be ensured that the SPP button is pressed first, followed
by the main trigger and the trigger button. When releasing, the SPP button must be released before the main
trigger and trigger buttons.
The following
information’s are transmitted:
Bootloader version
Firmware version
Version of the Bluetooth module used by the Ident-Ex
Address of the Bluetooth module used by the Ident-Ex
The 5 saved Bluetooth addresses of devices which have already been connected to the Ident-Ex via
Bluetooth.
Firmware information of the head module
3 Resetting to default settings
The firmware of the Ident-Ex can be used to reset the device to its factory settings. To enable this function,
the main trigger (trigger button on the underside), trigger (trigger button on the top) and SPP buttons must be
pressed and held for approx. 2 seconds when the Ident-Ex is starting up. Previous settings, such as
selection of the head module, main trigger and trigger button were not resetted and are retained.
4 Bluetooth Pairing of Ident-Ex and PC
If the Ident-Ex has not yet been paired with a PC, a pairing process must be performed before a Bluetooth
connection can be established between the Ident-Ex and PC. The Ident-Ex is using the SSP-Mode (Secure
Simple Pairing), in this case no pairing-password is required to pair with a device (Smartphone/Tablet or
PC).
Select the Bluetooth name of the Ident-Ex via
Start
->
Control Panel
->
Hardware and Sound
->
Add a
Bluetooth device
. The PC is now paired with the Ident-Ex and a Bluetooth connection can be established. A
Bluetooth connection (HID) may be established automatically after the pairing process. This is indicated by
the illuminating Bluetooth LED on the Ident-Ex (the SPP LED is off). However, since we need to establish a
Bluetooth connection in SPP to install firmware, an existing HID Bluetooth connection must be deleted. To
do this, press and hold the SPP button on the Ident-Ex for approx. 2 seconds until the Bluetooth LED goes
out. An SPP Bluetooth connection can now be established.
