7 | ZincBlue2 User Manual
Avertissements et mises en garde
ASC
Panneau / module de batteries
Pour éviter un incendie, un choc ou la mort, couper le courant au niveau du disjoncteur ou du fusible et vérifier que
l'alimentation est coupée avant de procéder au câblage, à l'entretien ou au démontage.
Lire ce manuel avant l'installation et l'utilisation. Si vous avez des questions concernant l'installation, le fonctionne-
ment ou l'entretien en toute sécurité, contacter le service d'assistance de ZincFive.
Déballer soigneusement les composants. Signaler immédiatement tout dommage lié au transport ou autre.
Ne jamais laisser des fils de batteries sous tension toucher l'ASC, le boîtier ou tout autre objet métallique.
Utiliser des techniques de levage appropriées lorsque l'ASC ou ses composants sont soulevés ou déplacés.
Dans des conditions de température ambiante élevée, la surface de l'ASC peut être très chaude au toucher lors de
son fonctionnement.
Veiller à ce que la ventilation soit assurée sur les côtés gauche et droit du boîtier de l'ASC.
Être installé et/ou utilisé conformément aux codes et réglementations électriques.
Avant l'installation, vérifiez que la tension d'entrée et les besoins en courant de la charge sont satisfaits par la sortie
de l'ASC. Vérifier que la tension et le courant de ligne répondent aux exigences d'entrée de l'ASC.
Pour éviter toute surcharge électrique, ne pas dépasser la puissance nominale.
Input Voltage Range
120Vac Nominal
85-140Vac User Programable
Input Current
15A max
Input Frequency
60Hz nominal
+/-10% (54 - 66Hz)
Output Voltage
/-3%
Output Current
8.3A Typical
Output Power
1,000VA Typical
Output Frequency
60Hz +/-0.5Hz
Output Waveform
Pure Sinewave
UPS Efficiency
0.97
ZincBlue2 UPS 1000W operating temperature range
-37°C to 74°C (-34°F to 165°F)
ZincBlue2 UPS 1000W
UL 1778 and CSA C22.2 No. 107.3 compliant in a maximum ambient environment of 40°C
Input Power
Environmental
Output
Regulatory Compliance
UPS Input & Output Values
L'installation et l'entretien des batteries doivent être effectués ou supervisés par un personnel connaissant les
batteries et les précautions requises.
Le panneau / module de batteries ne doit pas être installé dans une enceinte étanche, une ventilation doit
être prévue.
Utilisez des techniques de levage appropriées lorsque vous soulevez ou déplacez les batteries.
Ne jamais jeter de batteries dans un feu.
Ne jamais ouvrir ou endommager les batteries.
Une batterie peut présenter un risque de choc électrique et de courant de court-circuit élevé. Les précautions
suivantes doivent être observées lorsque vous travaillez sur des batteries
Retirer toutes montres, bagues ou autres objets métalliques.
Utiliser des outils avec des poignées isolées.
Débrancher l'entrée CA de la batterie avant de connecter ou de déconnecter les bornes de la batterie.
S'assurer que la batterie est éteinte avant de connecter ou de déconnecter les câbles
d'interconnexion de la batterie. Le voyant du panneau/module de la batterie sera éteint.
Ne jamais court-circuiter les broches à l'intérieur des connecteurs des câbles de la batterie.
Summary of Contents for ZincBlue2 UPS 1000W
Page 1: ...ZincBlue2 Manual...
Page 90: ...87 ZincBlue2 User Manual Notes...