background image

 

13 

Step 5. – Install Cartridge Filter and Attach Sump 

 

Remove the protective plastic wrap from the sediment pre-filter and place it in the cartridge 

filter housing sump.  At the bottom of the sump, there is a raised portion in the middle 

(standpipe) that will help center the filter in the housing.  The standpipe will fit inside the hole 

that runs through the middle of the filter cartridge.  Check to make sure that the black O-ring 

is seated properly in the grove at the top of the housing sump, then screw the housing sump 

containing the filter cartridge onto the cartridge filter housing cap.  Hand tighten only - do not 

use the spanner wrench.  Do not over-tighten!  Excessive force is not required to obtain a 

good seal. 

Step 6. – Connect Outlet Assembly to the ecoTAC™ Bypass Assembly 

 

Thread the outlet assembly on to the outlet side of one of the bypass assemblies as shown.  

This bypass assembly will be used on the ecoTAC™ system.  Note the position of the fitting 

stop.  The threaded collar of the outlet adapter should thread right up to the fitting stop.   

 

 

 

 

If there is a gap between the outlet adapter’s collar and the fitting stop, it is not threaded on 

far enough.  Excessive force is not required to obtain a good seal.  Do not over-tighten. 

 

Summary of Contents for EP-600-ULT

































Reviews: