Ser in u s 3 0 B en u tzer h an d b u ch 2 .1
Seite 56
3.5.20
Data Logging Menu (Datenerfassungsmenü)
Data Log Setup – Numeric
Diese Funktion ermöglicht das Erfassen von bis zu 12
Parametern. Nach dem Eintragen jeder Parameter (mit
dem Label „Logging Param. 1” – „Logging Param. 12”)
geben Sie die Nummer des zu erfassenden Parameters
ein.
Ein „255” bezeichnet das Ende der zu erfassenden
Parameterliste.
Data Log setup –Test
Diese Funktion bietet eine einfachere Alternative an,
erfasste Parameter auszuwählen. Statt eine Nummer
einzugeben, wählen Sie den Namen von der Liste.
Wählen Sie die Leerzeile, wenn Sie mit der Auswahl der
zu erfassenden Parameter fertig sind.
Data Log Interval
Stellen Sie das Intervall für die Erfassung von Messdaten
ein (1 Sekunde – 24 Stunden) oder wählen Sie
„disabled“, wenn Sie das Speichern von Daten auf dem
USB-Stick deaktivieren möchten.
Hinweis:
Die Erfassung einer Messung dauert ca. 1/3
Sekunde. Das Einstellen des Intervalls auf 1 Sekunde
kann die serielle Kommunikation verlangsamen.
+/- Keys
Die Parameter müssen in der Liste nacheinander
eingetragen werden. Beim Löschen eines Parameters
werden damit die sich darunter befindenden Parameter
automatisch nach oben verschoben. Die „–“-Taste löscht
das hervorgehobene Parameter; mit der „+“-Taste fügt
man ein neuer Parameter an der Stelle hinzu, was die
andere Parameter nach unten verschiebt.
3.5.21
Serial Communications (Serielle Kommunikation)
Multidrop ID
Dies ist die Identifikationsnummer des Analysators bei
Benutzung von Multidrop RS232-Kommunikation. 40
wird als Standardeinstellung übernommen, kann jedoch
geändert werden, wenn mehrere Serinus-Geräte über
dasselbe RS 232-Kabel angeschlossen sind.
Delay (RS232#2)
Wenn die Option „enabled” gewählt wird, wird die
serielle Kommunikation über die RS232#2-Schnittstelle
um ca. 0,25 Sekunden verzögert. Diese Funktion wird mit
Systemen benutzt, die mit der Schnelligkeit der Serinus-
Geräte nicht zurechtkommen. Wenn „disabled“ gewählt
wird, erfolgt die Kommunikation ohne Verzögerung.
Baud (RS232 #1)
Stellt die Baudrate dieses seriellen Kanals ein (1200,
2400, 4800, 9600, 14400, 19200 oder 38400).
Protocol (RS232 #1)
Stellt das Protokoll für diesen seriellen Kanal ein
(EC9800, Bayern, Advanced oder Modbus).
Summary of Contents for Serinus 30
