background image

 

 
 

1. RECOMMENDATIONS: 
 

- This Electrical Boiler is not intended for use by persons with reduced physical, sensory or 
mental  capabilities,  or  lack  of  experience  and  knowledge,  unless  they  have  been  given 
supervision or instruction concerning use of the Electrical Boiler by a person responsible for 
their safety.  
- It is not allowed, to play with the electrical boiler by CHILDREN. 
- It is necessary one to be familiar and to observe the safety operation and assembly manual. 
- After unpacking the boiler, check delivery integrity and completeness. 
-  Electrical  boiler  has  IP  20  protection  degree,  which  applies  after  an  installation  at  place 
where it will be used. 
- Check whether the boiler type corresponds to your needs. 
- It is recommendable for each assembly a project to be drafted. 
- The assembly may be carried out only by an expert, authorized for such activity. 
- Boiler assembly should meet the effective prescriptions, norms and to the present manual. 
- Connection of the boiler to the power network (if necessary) should be harmonized with the 
local  power  supplier,  which  should  be  done  by  the  consumer  prior  to  the  purchase  of  the 
boiler. 
- Adjustment and commissioning should be carried out only by a service technician approved 
by the producer. 
- Upon incorrect assembly, damages may occur and the producer shall not be liable thereof. 
- In case of failure contact the service organization. Unprofessional intervention may damage 
the boiler. 
- For correct functioning, safety and long-term operation secure prophylactics at least once a 
year. 
-  In case of damages  incurred by  unprofessional  assembly, as  well  as upon noncompliance 
with  the  regulations  and  the  operation  manual,  the  producer  is  not  liable  and  shall  not 
provide guarantee service. 
- The heating installation should have air bleeds at all necessary places.  
- It is not allowed to make any changes whatsoever on the electrical diagram of the product, 
except for connection of the indoor temperature or equithermal thermoregulator.  
-  Hydraulic  and  warm  tests  should  be  carried  out  of  each  heating  installation  upon 
commissioning. 
- The electric boiler may operate at open system up to temperature of 95

o

C max and at closed 

system up to 110

o

C at pressure of 1.8 bar in a self-contained heating circuit. 

- The assembly organization is obliged to get the client familiar with the operational rules of 
the heating system as a whole. 
 
 
 

2. INTRODUCTION 

 

The  flow-through  electric  boiler  ECOTERMAL  is  a  modern  ecological  source  of  heat 
designated  for  story  and  central  heating  of  small  and  average  size  houses  and  production 
facilities. The main advantages of heating with electric power are mostly cost effectiveness, 
high efficiency,  environmental  friendliness and  compactness. Electric boiler can be used in 

Summary of Contents for 10 MRT
















Reviews: