background image

EN

EN

2

1. Important Safety Instructions

When using an electrical appliance, basic precautions should always be followed, including 

the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
SAVE THESE INSTRUCTIONS

1. This Appliance is not intended to be used by children under 8 or anyone lacking knowledge 

on proper use. Supervision may be necessary. Do not allow children to play with the 

Appliance.

2. Do not use the Appliance in extremely hot or cold environments (below 0˚C/32˚F or above 

40˚C/104˚F). The Appliance can be used to clean outside windows if it is properly tethered 

to the Safety Pod, winds are calm, and it is not raining or snowing.

3. Please ensure the Appliance is plugged in while it is cleaning. The Appliance has a Back-Up 

Battery that charges during use. The Back-Up Battery powers the Appliance if it becomes 

unplugged or the electricity fails.

4. Do not leave the Appliance unattended when it is plugged in.

5. For household use ONLY. Do not use the Appliance in commercial or industrial environments.

6. Do not use the Appliance on cracked glass.

7. Only use accessories recommended or supplied by the manufacturer. Only use the Power 

Adapter supplied by the manufacturer.

8. Please make sure your power supply voltage matches the power voltage marked on the 

Power Adapter.

9. Do not use the Appliance on a framed window with a frame smaller than 5mm (0.2 inches). 

10. Do not use the Appliance on wet or greasy windows.

11. Store the Appliance away from heat and flammable materials.

12. Do not use the Appliance if it does not firmly attach to the glass or has visible signs of damage. 

13. To reduce the risk of electrical shock, do not put the Appliance in water or other liquid. Do 

not place or store Appliance where it can fall or be pulled into a tub or sink.

14. Do not touch power plug or the Appliance with wet hands.

15. Do not charge the Appliance in extremely hot or cold environments, or it may affect battery 

life span.

16. When charging the Appliance, do not place it on other electrical appliances and keep it 

away from fire and liquid.

17. Take care not to damage the power cord. Do not pull on or carry the Appliance by the power 

cord, use the power cord as a handle, close a window on the power cord, or put heavy 

weights on the power cord. Keep power cord away from hot surfaces.

18. Do not use with a damaged power cord or receptacle. Do not use the Appliance if it is not 

working properly, has been dropped, damaged, or come in contact with water. It must be 

repaired by the manufacturer or its service agent in order to avoid a hazard.

19. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent 

in order to avoid a hazard.

20. The plug must be removed from the receptacle before cleaning or maintaining the Appliance. 

Do not unplug the Power Adapter by pulling on the power cord.

21. The Back-Up Battery must be replaced by the manufacturer or its service agent in order 

to avoid a hazard. 

22. The Back-Up Battery must be removed and discarded according to local laws and regulations 

before disposal of the Appliance.

23. The Appliance must be disconnected from the receptacle before removing the battery for 

disposal of the Appliance.

Summary of Contents for WINBOT 930





















Reviews: