EcoWater ETF AIIF115 Owner'S Manual Download

Page: 19 / 24

Service Information

ECOWATER

S Y S T E

M S

MANUAL ADVANCE DIAGNOSTIC

Use the following procedures to advance the filter

valve through the regeneration cycles to check op-

eration.
Remove the top cover to observe cam and switch

operation during valve rotation.
DISPLAY MUST SHOW TIME AND DAY
1. Press and hold the RECHARGE keypad for 3 sec-

onds until RECHARGE NOW flashes in the display

and the filter moves into the backwash cycle.

...If the motor does not run, check the motor and all

wiring connections.
Look for a fast flow of water from the drain hose (see

specifications, page 4).
...An obstructed flow indicates a plugged top distrib-

utor, backwash flow plug, or drain hose.

NOTE:

Be sure household water pressure (well sys-

tem) is maintained at a minimum of 20 psi. Adjust the

pump switch upward, if needed.

2. Press the RECHARGE keypad to move the filter

into fast rinse. Again, look for a drain flow rate about

the same as backwash.

3. To return the filter to service, press the RE-

CHARGE keypad once.

OTHER SERVICE

UNFILTERED WATER BYPASS (unfiltered water

“bleeds” into filtered water supply.

1. Missing or defective o--ring(s) at resin tank to

valve connection (see pages 20 and 21).

2. Defective rotor disc, seal or wave washer (see

pages 22 and 23).

WATER LEAKS FROM DRAIN HOSE (during ser-

vice)

1. Defective rotor disc, seal, or wave washer.

2. Defective o--ring on disc shaft.

AUTOMATIC ELECTRONIC DIAGNOSTICS

The face plate has a self diagnostic function for the

electrical systems (except input power). The face

plate monitors the electronic components and cir-

cuits for correct operation. If a malfunction occurs,

an error code appears in the face plate display.

POSSIBLE DEFECT

CODE

MOST LIKELY

----------------------------------------------------------------------------------------------

LEAST LIKELY

Err 01, Err 03

& Err 04

wiring harness or connection to position switch / switch / valve defect causing high torque / motor

inoperative

Err 05

faceplate

PROCEDURE FOR REMOVING ERROR CODE FROM FACEPLATE:

1. Unplug transformer-------- 2. Correct defect-------- 3.

Plug in transformer-------- 4. Wait for 12 minutes. The error code will return if the defect was not corrected. Press and hold the RECHARGE
keypad for 3 seconds as an alternate way to clear an error code.

Summary of Contents for ETF AIIF115

























Search results

Summary of Contents for ETF AIIF115

Reviews:

Related manuals for ETF AIIF115

Brands by name

Popular brands

EcoWater ETF AIIF115, Owner'S Manual

Search results

Summary of Contents for ETF AIIF115

Reviews:

Related manuals for ETF AIIF115

Brands by name

Popular brands