EcoWater ETF AIIF115 Owner'S Manual Download

Page: 8 / 24

Planning Installation

ECOWATER

S Y S T E

M S

TOOLS YOU MAY NEED

common screwdriver

pliers

cross--point screwdriver

tape measure

SOLDERED COPPER

THREADED

CPVC PLASTIC

tubing cutter

hacksaw or

pipe cutter

hacksaw

propane torch

threading tool

adjustable

wrench

LEAD--FREE

solder and flux

pipe joint com-

pound*

solvent cement*

emery cloth,

sandpaper or steel

wool

primer

MATERIALS YOU MAY NEED

bypass valve, or 3 valves

pipe and fittings as required

5/8” I. D. minimum drain hose, either standard gar-

den hose, or hose onto a barb fitting*

VALVE DRAIN OPTIONS:

Flexible drain hose is

not allowed in all localities (check your codes). For

a rigid valve drain run, plumb according to local

codes. To connect to the valve drain fitting, pur-

chase an adaptor, garden hose thread x 5/8” (mini-

mum) tube. Use a hacksaw to cut barbs from the

fitting.

SELECT INSTALLATION LOCATION

Consider all of the following when selecting an

installation location for the filter selected.

To filter all water in the home, install the filter close

to the water supply inlet. To conserve filtered wa-

ter, outside faucets should remain on raw water.

If other water conditioning equipment is installed,

locate as shown in Figure 4.

A nearby drain is needed to carry away regenera-

tion discharge water. A floor drain is preferred,

with a laundry tub, standpipe, etc., as other op-

tions (check your local codes).

The filter works on 24 volts only. A transformer is

included (FOR INDOOR USE) to reduce

115V--60 Hz house electrical power. Provide an

approved, grounded outlet within 10’ of the filter.

The filter includes a 10’ power cable for connec-

tion between the transformer and the timer. The

relay box also requires a suitable live, grounded

outlet.

Position the filter at least 6” from surrounding

walls, or other appliances, to allow access for

servicing.

If installing the filter in an outside location, be sure

to provide protection from the elements, contami-

nation, vandalism, and sunlight heat. The sun’s

heat can melt plastic parts.

FIGURE 4

Well

Pump

Pressure

tank

Water

Softener

Taste &

Odor

Filter

Chemical

Feed System

Air Injected

Iron Filter

Water

Neutralizer

Filter

Sediment

Filter

Blending

Tank

HOT

COLD

OUTSIDE

FAUCETS

Water

Heater

Summary of Contents for ETF AIIF115

























Search results

Summary of Contents for ETF AIIF115

Reviews:

Related manuals for ETF AIIF115

Brands by name

Popular brands

EcoWater ETF AIIF115, Owner'S Manual

Search results

Summary of Contents for ETF AIIF115

Reviews:

Related manuals for ETF AIIF115

Brands by name

Popular brands