background image

Pretty - Nice - LADy

11

F

D

IT

UK

Warning

installation and extraordinary maintenance must be done only by skilled, technical personnel.

•  important notE

: if the stove is connected to the outside by a metal flue gas ex-

haust pipe, two conditions could be deleterious to good combustion.

1- if the horizontal part of the flue gas exhaust pipe is too long, this will worsen the quality 

of  combustion  and  noticeably  increase  ash  residues  in  the  grate.  For  this  reason  the 
electronics board has a facility for regulating both the exhaust pressure and pellet loading 
rate. this should be carried out only by the installer technician, at installation or when 
conditions make it necessary.

2- A vertical metal exhaust pipe that is three / four metres long will increase the combus-

tion rate. this will cause the stove to go out at the minimum power level. to prevent this 
just increase the selected power level or change the original settings.

MAINTENANCE OF THE SMOKE ExHAUST DUCT

•  Annually,  we  recommend  cleaning  the  smoke  exhaust  duct  in  order  to  prevent  self-

combustion of any soot and powder that may be deposited there.

•  in case of fire switch off the stove immediately and disconnect it from the power supply.

Summary of Contents for Lady

















Reviews: