background image

FCC STATEMENT:

This device complies with Part 15 of the FCC 
Rules. Operation is subject to the following 
two conditions:

  1) This device may not cause harmful 
 interference, 

and

 2) This device must accept any interference 
 

received, including interference that may 

 

cause undesired operation.

WARNING:

 Changes or modifications not 

expressly approved by the party responsible for 
compliance could void the user’s authority to 
operate the equipment.

NOTE:

 This equipment has been tested 

and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of 
the FCC Rules. These limits are designed to 
provide reasonable protection against harmful 
interference in a residential installation. 
This equipment generates, uses, and can 
radiate radio frequency energy and, if not 
installed and used in accordance with the 
instructions, may cause harmful interference 
to radio communications. However, there is 
no guarantee that interference will not occur 
in a particular installation. If this equipment 
does cause harmful interference to radio or 
television reception, which can be determined 
by turning the equipment off and on, the user is 
encouraged to try to correct the interference by 
one or more of the following measures: reorient 
or relocate the receiving antenna, increase 
the separation between the equipment and 
receiver, connect the equipment into an outlet 
on a circuit different from that to which the 

Power On, Battery, & 
LED Status Indicators

Once fully charged, press the 
Standby Power Button

 

on 

the top of your EcoEdge. You 
will see the green LED light 
& you will hear, “Power on” 
when powering on.

IMPORTANT:

 Make sure that the 

Main Power Switch, located in 
the back compartment under the 
cap, is set in the ON position. If 
the switch is in the OFF position, 
your EcoEdge will not be able to 
turn on using the Standby 
Power Button.

The LED battery level indicators 
are located on the top of the unit. 
Each bar represents 25% of a 
charge, with 4 full LEDs indicating 
a full charge.

Audio playback time over 
Bluetooth connection is 
approximately 20 hours.

2

Summary of Contents for EcoEdge GDI-EXEDGE301

















Reviews: