background image

INSTALLATION MANUAL AND OPERATING INSTRUCTIONS

NOTICE

Used to address practices not related to personal injury�

CAUTION

Indicates a hazardous situation which, if not avoided, 

could result in minor or moderate injury�

!

!

  

 WARNING

Indicates a hazardous situation which, if not avoided, 

could result in death or serious injury�

!

  

DANGER

Indicates a hazardous situation which, if not avoided, 

WILL result in death or serious injury

!

  

This is the safety alert symbol�  Symbol alerts you to      

potential personal injury hazards� Obey all safety messages 

following this symbol to avoid possible injury or death�

Become familiar with symbols identifying potential 

hazards

 WARNING

Fire, explosion, asphyxiation and electrical shock 

hazard�  Improper installation could result in death 

or serious injury�  Read this manual and understand 

all requirements before beginning installation�

!

  

DAN

IMPORTANT:

 

Read and understand the fol-

lowing instructions COMPLETELY before install-

ing!!

Introduction

This manual is intended to familiarize the installer and user 

of the Argo DPM-2 Outdoor Temperature Setback Control 

with its installation and operation to assure normal trouble-

free operation�

Argo controls are designed and manufactured with quality 

components for maximum life and durability and require 

minimal service� To ensure a satisfactory installation, it is 

imperative that the instructions be followed carefully before 

operating the control� Failure to do so may result in breach 

of warranty�

Product Description And Specifications

DPM-2 Outdoor Temperature Setback Control is designed 

to raise or lower the temperature of boiler supply water 

based upon a proportionate drop or rise in temperature 

at the outside sensor� This control plugs into Argo control 

equipment with a data port or as a stand alone device that 

can be easily wired into almost any system�

WARNING

Fire, Explosion, Asphyxiation, Electrical shock 

hazard! Flooding will result in damages such as 

electrical problems, corrosion, inoperative parts, 

mold and other unforeseen issues which can 

occur over time� Any equipment determined by 

a professional as damaged by a flood, defined 

as excess of water or other liquid, shall be 

replaced� Failure to follow these directions will 

result in a Hazardous Situation�

!

  

3

PN 240005132 Rev. D [11/15/2021]

Summary of Contents for ARGO DPM-2













Reviews: