background image

WWW.EDELBROCK.CO

M

©2007 Edelbrock Corporation
Brochure #63-70216

Page 11 of 16

Catalog #70216

Rev. 5/07 - DC/mc

3.2 Wide Open Throttle Module Wiring Diagram

3.3 Nitrous Electrical System Installation Procedure

Determine a location for the wIde open throttle relay and fuse holder wire. Most common installations locate these components
close to the battery. However, these connectors are water resistant, not waterproof, so care is required when mounting this
assembly under the hood of your vehicle.

Wire Schematic Origin and Destination Map

Wire Color

System

Origin

Destination

Terminal Used

Red

Main System Power

WOT Module

B12V Signal

Ring

Yellow

Solenoid Power

WOT Module

Solenoid

Spade

Blue

TPS 5 Volt Input

WOT Module

Arming Switch

Spade

Blue

TPS 5 Volt Input

Arming Switch

TPS Sensor

Splice Connector

Black

Wide Open Throttle Module

WOT Module

Chassis Ground

Ring

Black

Solenoid Ground

Solenoid

Chassis Ground

Ring

Black

Solenoid Power In

Solenoid

WOT Module

Spade

Br/Or

TPS 5 Volt Reference

Throttle Body

ECM Harness

-

3.4 Wide Open Throttle (WOT) Module Installation

The WOT module includes 3 feet of color-coded wires and terminals to make the electrical system installation for your Edelbrock
Nitrous System as easy as possible. We recommend that you do not cut any lengths of wires from the wire harness or complete
the wiring of the system until all of the mechanical components are securely mounted in their permanent locations.

Once all the solenoids and switches are placed, route the un-cut wires from the harness to each location allowing enough wire
length on each circuit to not interfere with operating linkages, heat sources, brackets, etc. Pay particular attention to sharp edges
along the route of your wire harness as they can chafe the wire and cause your system to fail.

Once you have decided the location of the “WOT” module secure it with fasteners (not included with kit) such as sheet metal
screws, bolts & nuts, etc. Allow for some slack in the red wire that connects the “WOT” moduel and fuse holders together.

Battery

Ground

Fuse

w/Holder

Red

Black

Blue

Yellow

Nitrous

Solenoid

Fuel

Solenoid

Ground

Ground

Brown/Orange Wire

Black Connector

Located on

Throttle Body

Wide Open Throttle

(WOT) Module

Summary of Contents for 70216

















Reviews: