background image

 

 

Thank you for choosing the EdenPURE

®

 Classic Plus Infrared Heater. This owner’s manual will 

provide you with valuable information necessary for the proper care and maintenance of your 
new product. Please take a few moments to thoroughly read the instructions and familiarize 
yourself with all the operational aspects of your new heater.  

 
 

IMPORTANT INSTRUCTIONS 

 

WARNING

 

IMPROPER USE OF THIS HEATER COULD RESULT IN RISK OF FIRE, ELECTRIC SHOCK,  

AND/OR PERSONAL INJURY 

WARNING

 

ANY REQUIRED SERVICE SHOULD ONLY BE  

PERFORMED BY AN AUTHORIZED SERVICE REPRESENTATIVE AND ANY  

OTHER REPAIRS ATTEMPTED BY ANYONE OTHER THAN AN AUTHORIZED 

SERVICE REPRESENTATIVE WILL VOID THE WARRANTY. 

FOR AUTHORIZED SERVICE, CALL 1-800-225-6595 OR VISIT WWW.EDENPURESUPPORT.COM 

WARNING

 

RISK OF ELECTRICAL SHOCK. DO NOT OPEN. 

NO USER-SERVICEABLE PARTS INSIDE.

 

 

1.

 

Read ALL instructions before using the EdenPURE

®

 Classic Plus. 

2.

 

CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself. 

3.

 

This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot 
surfaces. If provided, use handles when moving this heater.  

4.

 

Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and 
curtains at least 3 ft. from the front of the heater and keep them away from the sides, top, 
and rear. DO NOT place towels or other objects on the heater.  

5.

 

Extreme caution is necessary when any heater is used by or near children or the disabled, 
or when the heater is left operating and unattended. 

6.

 

DO NOT operate any heater with a damaged cord or if the heater malfunctions, has been 
dropped or damaged in any manner. Return heater to authorized service facility for 
examination, electrical or mechanical adjustment, or repair. 

7.

 

This heater is not intended for use in bathrooms, laundry areas and similar indoor 
locations. NEVER locate heater where it may fall into a bathtub or other water container. 
To protect against electrical hazards, DO NOT immerse in water or other liquids.  

8.

 

DO NOT touch the control panel or plug with a wet hand.  

9.

 

DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or 
similar coverings. Arrange cord away from traffic area and where it will not be tripped 
over. 

10.

 

DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as 
this may cause an electric shock or fire, or damage the heater. 

11.

 

To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO 
NOT use on soft surfaces, like a bed, where openings may become blocked.  

Summary of Contents for A5834










Reviews: