background image

Cleaning the electrostatic filter 

The heater has an electrostatic filter located at the rear. The cleaning of the 
filter should be performed once per month or as needed (when dust is visible 
on the filter) to ensure efficient operation of the heater. 

 

1. Power the heater OFF by pressing the POWER button located on the left 

side of the Control Panel. 

 

2. Unplug the heater’s power cord. 

 

3. Turn the stopper 90

 clockwise/counterclockwise. (Figure 1). 

 

4. Remove the filter by pulling down and out (Figure 2). 
 
5. Clean the filter by vacuuming. 
 
6. Replace the filter by sliding the filter into the gap. 
 

 
 
 
 
 
 
 
 

 
Warning: 

Any other servicing needed must be performed by an authorized 

service representative. Do not attempt to service the unit yourself. 
 

Product Specifications 
 
Model No.

A5955

 

Voltage

: 120V, 60Hz 

Current

: Maximum continuous draw: 

           

    12.5 amps     

       

Output

: 5200 BTUs 

Power

: 1500 Watts 

Blower

: Multi-blade; Low Noise, High Pressure 

 

In The Box 

  DR Infrared Portable Space Heater 

  F

ee

t (4 pcs)   

  Remote 

C

ontrol (1 battery) 

  User’s Manual 

 

Figure 2

 

Figure 1

 

Quick Start Guide

Summary of Contents for A5955

















Reviews: