READ ALL INSTRUCTIONS BEFORE USING THE HEATER
Operation
– 8-step setup for EdenPURE
®
1) Lift heater from box. We recommend keeping the packaging for off-season storage and any transport needs.
2) Find a level and unobstructed location to place the unpackaged heater.
3) Plug the power cord directly into an unused grounded 110 volt 15 amp or higher circuit receptacle. The power button will illuminate and the heater will beep, indicating
the unit is plugged into the receptacle.
4) If using the optional remote, insert battery into the battery compartment on the remote control.
5) Push the “Power” button located on the front of the heater or the remote control to turn the heater on. Set the Mode Key to “Auto”. Adjust the “temp up” and “temp down”
buttons until the desired temperature level is indicated. Once the desired temperature is reached, the heater will cycle on and off to maintain the room temperature. When
the Heater is set on the “Auto” mode and cycling off and on, it has been equipped with an Energy Savings feature. The unit will run on full power until it gets to within 2
degrees of the desired temperature. At this point it will automatically go into an energy savings mode which will dim the heating elements and lower the wattage and the
fan speed. Not only will this save energy, it also keeps the room temperature closer to the desired temperature. The fan will run periodically to circulate the room air
through the heater in order to monitor the room temperature more accurately. If the room temperature should fall below 2 degrees of the desired temperature, the unit will
return to the full power mode until the desired temperature is reached again.
6) Switch the Mode Key to “High” in order to have the heater stay on high heat and not cycle on and off.
7) To turn the heater off, press the “Power” button; the fan will continue to run until all of the heat has been expelled and will then turn off.
8) The heater is equipped with a temperature limiting control contained inside the unit. If the heater stops working, shut the power off, unplug unit and let the unit cool down
(Approximately 30-45 minutes), plug in unit, turn the power back on and resume use. If the unit continues to shut down or the unit does not reset itself, please call
1-800-219-8458.
Cabinet Care
– Wipe clean with a soft damp cloth.
Heater Storage
– When the heater is not going to be used for an extended period of time, please do the following:
1) Unplug the heater.
2) Wind up electrical cord so as to keep it off of the ground.
3) Cover the heater to prevent dust from accumulating on filter or internally.
4) Store the heater in a dry, low dust environment.
Service
– To replace a heating element or for other repairs or service, call 1-800-219-8458.
WASHABLE LIFETIME FILTER SYSTEM
EdenPURE
®
Heaters come equipped with a washable lifetime filter on the rear of the unit that is easy to clean.
IMPORTANT INFORMATION: If you have allergies and/or are sensitive to dust, you will want to use this filter. When choosing to use the filter, it
must be cleaned daily; a clogged filter will cause the heater to not work to its full capacity.
Using the heater with the dust filter attached is an optional feature. Operating the heater without the filter will in no way harm or alter the operation
of the heater. If you are not sensitive to dust or do not want to clean the filter daily, please remove it from the back of unit and use your heater
without it.
To clean the filter:
1) Press the tab(s) on the top of the filter cover to release the filter.
2) Run warm tap water over the filter, the opposite direction of air flow, until water runs clear. The filter might excrete some filtered residue, so be
cautious not to drip on any stainable surfaces such as carpeting. You can also soak the filter in water mixed with a small amount of mild dish
soap (don’t forget to rinse with water after soaking filter).
3) Shake the filter over a sink until excess water is removed and allow it to drip dry completely before reinstalling. DO NOT force the filter to dry
using any alternative methods.
4) Reinstall the filter to the rear of the unit by positioning the filter back in place and securing the filter cover back into the locked position.
To assure maximum performance of the EdenPURE
®
heater, please note the following recommendations:
1) For best results, do not locate the heater in an area with a high rate of air filtration and movement as the warm air will be exhausted.
2) Try placing the heater near a warmer inside wall and direct the output toward a cooler outside wall. The cooler outside wall will tend to draw
the generated heat toward itself, which will allow for more efficient heating.
3) Placing the heater next to a cold air return will draw the heat away from area to be heated. Try closing or covering the cold air return. This will
allow for more efficient heating. Experiment with the placement of the heater to see what works best for you.
4) To ensure maximum efficiency, a 40% (minimum) relative humidity should be maintained in the heated environment.
5) The heaters are designed to operate for maximum efficiency up to 70-72 degree range. Due to the soft heat concept, a temperature of 68
degrees will feel as though it were 72 degrees. This is due to the heat mixing evenly with humidity for “head-to-toe” comfort.
6) When the heater is placed in an isolated area, i.e. basement or recreation area, the delivery registers and air return grills of the
existing system should be closed in that area if possible.
7) In rooms with large areas of bare concrete, try placing the heater a few feet above the floor. Make sure the heater is secure and won’t fall. This
will allow for more efficient heating since concrete acts as a heat sink and will tend to draw the heat in its direction.
8) Try lowering your central heating system to a lower temperature and placing the heater in the area you spend the majority of your time. Now
set the EdenPURE
®
heater to your comfort level. After all, there is no point heating multiple rooms to 68+ degrees when they are not in use.
9) When heating larger areas, place the heater in a central location. If a ceiling fan is nearby, try using it at the same time to help distribute the heat evenly.
Our suggestion, give it a try and see what works best for you.
10) If used in an extremely dirty or dusty area, the filter must be cleaned more frequently as it can clog and cause the heater to stop working.
11) The heater grill is hot when in use. To avoid burns, do not let bare skin touch hot surface. Keep combustible materials, such as furniture, pillows, bedding,
papers, clothes, and curtains at least three feet from the front of the heater and keep them away from the sides and rear.
12) Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
13) To disconnect the heater, press power button to “off,” then remove plug from outlet once it has stopped running.
14) Always unplug heater when not in use.
