background image

 
 

270900_00 | 09.2021 

EDER Power Climber 

24

 

 

EN 

WARNING 

Additional rope inspection and frequent replacement 

If no belay rope is used, increased attention must be paid to the 
ascent rope: 
>  Check the rope with the greatest possible attention for dirt and 

heavy abrasion before each use. Replace the rope even if it is 
only slightly worn.  

>  If the rope slips, i.e. the sheave rotates but the device does not 

ascend  on  the  rope,  the  motor  must  be  switched  off 

immediately

 

The rope will wear out within a few seconds if it slips and 
can be heavily damaged, or even break. 

 

Lifting operations  

 
When  lifting  loads,  follow  the  current  work  safety  regulations  in  your 
country. 
 
Basic safety rules when lifting are: 

Staying under suspended loads is prohibited 

Keep your distance from the load 

Do not pull at an angle to the load 

Always keep an eye on the load 

Make sure that communication is ensured 

The maximum permissible load (240kg) must not be exceeded. 

EPC 130: 130kg 
EPC 240: 240kg 

Starting the engine 

See the separate instruction manual for the engine. 

Operation 

To climb the rope, the operator hooks into the EDER Power Climber's 
carabiner  loop  with  his  carabiner  on  the  climbing  harness  or  with  a 
webbing sling.  

Summary of Contents for EPC 130

































Reviews: