background image

12

6. Close supervision is necessary when any appliance is used by or near 

children by the handicapped or the infirm.

7. Do not use honing oils, water or any other lubricant with the 

Chef’sChoice

® 

601. 

8.

SAVE THESE INSTRUCTIONS.

SERVICE 

In the event post-warranty service is needed, return your blade sharpener to the
EdgeCraft factory where the cost of repair or adjustment can be estimated before
the repair is undertaken. 
Please  include  your  return  address  and  a  brief  description  of  the  problem  or 
damage to the blade sharpener on a separate sheet inside the box.

Made in the U.S.A.

www.edgecraft.com 

U.S. Patent Pending. 
© EdgeCraft Corporation 2007
D07

S601200

EdgeCraft Corporation

825 Southw ood Road,

 Avondale,

 PA 19311 U.S.A.

Customer Service

1-800-342-3255

Used with normal care this EdgeCraft product, designed for hand use only, is guaranteed against
defective  material  and  workmanship  for  a  period  of  one  (1)  year  from  the  date  of  purchase
(“Warranty Period”). We will repair or replace at our option, any product or part that is defective in
material or workmanship without charge if the product is returned to us postage prepaid, with dated
proof of purchase, within the Warranty Period. This Limited Warranty does not cover replacement of
the  steel  rods  necessitated  by  use  of  the  product  or  product  damage  resulting  from  misuse. 
ALL IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE,  ARE LIMITED TO THE WARRANTY PERIOD.  EDGECRAFT
CORPORATION SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some
states do not allow limitations on how long an implied warranty lasts and some states do not allow
the  exclusion  or  limitation  of  incidental  or  consequential  damages,  so  the  above  limitations  or 
exclusions man not apply to you. This Limited Warranty gives you specific legal rights, and you may
also have other rights which vary from state to state. 

This warranty applies only to normal household use of this sharpener and is void for industrial or
commercial use. 

Summary of Contents for Diamond Hone 601













Reviews: