6
G
D
H
A
B
F
C
E
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DO NOT SCALE DRAWING
FLOOD_BUSTER_FULL_ASSEMBLY
SHEET 3 OF 3
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:4 WEIGHT:
REV
DWG. NO.
E
SIZE
TITLE:
ENGINEERING DIVISION
1753 BLAKE AVENUE
LOS ANGELES, CA 90031
NAME
DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL 1/32
ANGULAR .5
TWO PLACE DECIMAL .02
THREE PLACE DECIMAL .005
APPLICATION
USED ON
NEXT ASSY
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
EDIC. ANY REPRODUCTION IN PART OR
AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF EDIC IS PROHIBITED.
1
3
5
7
2
8
9
10
11
12
13
14
15 16
4
5
7
7
1
7
12
11
FB50 MACHINE LAYOUT OVERVIEW:
1. TANK LID: Provides seal for vacuum system when
closed and allows access to tank and debris basket
when removed.
2. VACUUM INTAKE BARB: Allows vacuum hose to
be attached to machine to pull in fluid.
3. DEBRIS BASKET WITH GASKET: Removes larger
solids. from incoming water stream while gasket cre-
ates vacuum seal between tank and lid.
4. HANDLE: Used to maneuver and position equip-
ment.
5. LID LOCKING LATCH: Used to lock or release the
tank lid.
6. TANK: Houses pump and holds waste water
4
6
7. HOSE SUPPORT: Supports a hose when hose is
wrapped around machine. Has hook openings for
bungee cords. (Bungee cords not included)
8. PUMP SWITCH: Controls power to pump
9. VACUUM SWITCH: Controls power to vacuum
10. COLD AIR INTAKE: Cools vacuum motor.
11. FRONT LOCKING CASTERS: Allows machine to be
locked into place to prevent unwanted movement.
12. REAR WHEELS
13. DISCHARGE HOSE HOOKUP: Connects to pump
out hose.
14. WASTE WATER DUMP VALVE: Allows manual
dumping of waste water.
15. VACUUM EXHAUST PORT
16. TWIST LOCK POWER INLET: Hooks up to main
power cord
G
D
H
A
B
F
C
E
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DO NOT SCALE DRAWING
FLOOD_BUSTER_FULL_ASSEMBLY
SHEET 3 OF 3
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:4 WEIGHT:
REV
DWG. NO.
E
SIZE
TITLE:
ENGINEERING DIVISION
1753 BLAKE AVENUE
LOS ANGELES, CA 90031
NAME
DATE
COMMENTS:
Q.A.
MFG APPR.
ENG APPR.
CHECKED
DRAWN
FINISH
MATERIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL 1/32
ANGULAR .5
TWO PLACE DECIMAL .02
THREE PLACE DECIMAL .005
APPLICATION
USED ON
NEXT ASSY
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
EDIC. ANY REPRODUCTION IN PART OR
AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF EDIC IS PROHIBITED.
Summary of Contents for FLOODBUSTER FB50
Page 10: ...9...
