background image

- 46 

-

ENGLISH

INSTALLATION

fig. 23

X

fig. 24

Y

NOTES ON FITTING THE COVERING
In using a prefabricated Edilkamin covering, to identify the 
exact position of PELLKAMIN  is important to verify the mo-
del of the covering to be used. 
Positioning differs according to the model chosen (see as-
sembly instructions given in the packaging of each covering). 
Always check that installation is perfectly vertical and horizon-
tal.

COVERINGS, COUNTER-HOODS AND THEIR 
VENTILATION
Before installing the covering, check that all connections, com-
mands and moving parts are perfectly functional.
Check this with the insert on and working for a few hours. Do 

so prior to fitting the covering in order to intervene as necessa

-

ry.
Finishing works, such as construction of the counter-hood, 
covering assembly, pilaster preparation, painting, etc.,

should be carried out once the final test has been passed.

Edilkamin will therefore not be held liable for any charges 
deriving from both demolition and reconstruction works,
even where consequent to replacement of any faulty insert 
parts.

Rather, at least 1 cm. (approx.) space must be left to allow 

air to flow, thereby preventing heat from accumulating.

The counter-hood can be created from fireproof plaster

-

board panels or plaster sheets. When creating this, the air 

circulation grill must be included, as previously specified.

- THE MANTEL CAN BE CONSTRUCTED WITH FIRE 
RESISTANT PANELS IN PLASTERBOARD OR
GYPSUM BOARD. 
- AERATION GRILLES FOR PREVENTING ANY 
EXCESS TEMPERATURE INSIDE MUST BE PROVI-

DED FOR DURING CONSTRUCTION (fig. 23).

During the construction phase of the covering it is funda-
mental to ensure that the combustion air is restored
to prevent pressure phenomena in the room where the 

fireplace is installed (refer to the Chapter regarding the 

external air inlet on page 40)

In addition to the above, always consider the indications 
given by paragraphs 4.4 and 4.7 of standard UNI 10683

“insulation, finishes, coverings and safety recommenda

-

tions”.

N.B.: IMPORTANT FOR INSTALLATION CONDITIONS

*

 Provide two aeration grilles (area larger than 100 cm

2

),  the 

first one under the insert and the second positioned at least 50 

cm above the insert or anyway communicating with the internal 
compartment where the insert is positioned.
These grilles prevent the accumulation of heat inside, which is 
then used to help heat the room of installation.

Internal mantel

ventilation grilled

External 
intake

Recycled air 

intake inspection

METAL PROFILE FINISHING PLATE (X) FOR 
MOUNTING OF “FRAME” COVERINGS 
(supplied) 

After removing the lower grille, you can mount, on the lower 

base of the structure, the “angular” metal finishing profile (

– for “frame” coverings or plasterboard) in place of the metal 

profile plate (

Y) previously mounted (see Fig. 24).

Summary of Contents for PELLKAMIN 10

































Reviews: