background image

- 32 

-

ENGLISH

• The appliance is not designed to be used by people, including 
children, with reduced physical, sensorial or mental abilities. 
Children must be supervised to ensure they do not play with 
the appliance.

• The main risks that may derive from using the insert pertain
to non-compliance with installation instructions, direct contact

with live electrical parts (internal), contact with the fire or hot

parts (glass, pipes, hot air output), when extraneous substances 
or non-recommended fuel are introduced, or due to incorrect 
maintenance or by repeatedly pressing the ignition button wi-
thout having emptied the crucible.

• Only use certified, high quality, 6 mm diameter wooden 

pellets for fuel.

• Should components fail, the insert are equipped with safety
devices that guarantee automatic shutdown. These are activated
without any intervention required.

• In order to function correctly, the insert must be installed in
accordance with the instructions given herein and the door
must not be opened during operation: combustion is fully
automatic and requires no intervention.

• Under no circumstances should any foreign substances be
entered into the hearth or hopper.

• Do not use flammable products to clean the smoke channel

(the flue section connecting the stove smoke outlet to the

chimney flue). 

• The hearth and hopper parts must only be cleaned when 
COLD.

• The glass can be cleaned when COLD with a suitable product
(e.g. GlassKamin Edilkamin) and a cloth.

• Avoid opening the door of the combustion chamber when the 
insert is hot; wait until it has cooled down naturally.

• Each time the insert is removed, a security system cuts off the 
power supply. Should the insert be removed involuntarily du-
ring ignition, operation or while switching off (including while 
blocked), the “Power failure” block phase will be launched 
when the insert is reinserted. Wait for the block phase to end 
before reactivating the insert.

SAFETY INFORMATION

• The insert must not function if the door is open, if the glass is 
broken or if the pellet-loading port is open.

• It must not be used as a step ladder or a base on which to rest 
any object.

• Do not lay laundry directly on the insert to dry. Any clothes 
horse or similar must be placed at a safe distance from the 

insert (danger of fire).

• Make sure the insert is installed and ignited the first time 

by Edilkamin-qualified CAT personnel (technical assistan

-

ce centre) in accordance with the instructions provided here 
within; this is an essential requirement for the validation of the 
guarantee. 

• When the insert is in operation, the exhaust pipes and door
become very hot (do not touch without wearing the thermal
glove).

• Do not place anything, which is not heat resistant near the
insert.

• NEVER use liquid fuel to ignite the insert or rekindle the 
embers.

• Do not obstruct the ventilation apertures in the room where
the insert is installed, nor the air inlets of the stove itself.

• Do not wet the insert and do not go near electrical parts
with wet hands.

• Do not use reducers on the smoke exhaust pipes.

• The insert must be installed in a room that is suitable for fire 

prevention and equipped with all that is required (power and 
air supply and outlets) for the insert to function correctly and 
safely.

• SHOULD IGNITION FAIL, DO NOT RE-IGNITE UN-
TIL YOU HAVE EMPTIED THE COMBUSTION CHAM-
BER.

Summary of Contents for PELLKAMIN 10

































Reviews: