153
8.
I forgot my password.
a.
Reset the router to its factory default settings and use the default username
admin
and default password
1234
. Default settings are displayed on the product
label on the bottom of the device, as shown above.
9.
My BR-6208AC V2 has a weak wireless signal.
Weak signals are usually caused by interference from other devices or obstacles
blocking the BR-6208AC V2
s i eless sig al:
a.
Keep the device away from other radio devices such as microwaves or cordless
phones.
b.
Do not put the device in the corner of a room or under/nearby metal.
c.
Ensure there are as few obstacles as possible between the BR-6208AC V2 and
your wireless network device.
In range extender mode
, the BR-6208AC V2
s eak i eless sig al a e i tu
aused a eak sig al f o ou e isti g oute . It s i po ta t to hoose a good
location for the BR-6208AC V2
in relation to your existing wireless router
. The best
location is roughly in the middle between your existing wireless router and the area
you would like to be covered by the BR-6208AC V2. If you are too far away from
your existing router, then it is difficult for the BR-6208AC V2 to receive a wireless
signal.
10.
Do the Internet and LAN ports work the same when the device is
in different modes?
No, the Internet and LAN ports have slightly different functions depending on
the operating mode of the device.
a.
In
Wi-Fi router
mode, the
Internet port
is for a direct connection to your xDSL
modem. The
LAN ports
are for wired network clients.
b.
In
access point
mode, the
Internet port
is not functional. Connect your existing
oute to the de i e s
LAN port
, and the other
LAN ports
can connect wired
network clients.
c.
In
range extender
mode, the
Internet port
is not functional and the all of
LAN
ports
are for wired network clients. Do not connect your existing router to the
de i e s
Internet
or
LAN ports
, as this can cause the device to malfunction.
d.
In
wireless bridge
mode, the
Internet port
is not functional and the all of
LAN
ports
are for wired network clients.
e.
In
WISP
mode, the
Internet port
is not functional and the all of
LAN ports
are for
wired network clients.
11.
A firmware upgrade failed and the BR-6208AC V2
is ’t orki g.
Summary of Contents for BR-6208AC V2
