background image

FCC WARNING 

This equipment has been tested and found to comply with the limits for a 
Class B Digital device, pursuant to part 15 of the FCC Rules.    These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation.    This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance 
with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not 
occur in a particular installation.    If this equipment does cause harmful 
interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna 

 

Increase the separation between the equipment and receiver 

 

Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected 

 

Consult the dealer or an experienced radio/TV technician for help 

You are cautioned that changes or modifications not expressly approved by 
the party responsible for compliance could void your authority to operate 
the equipment. 
 
This device complies with part 15 of the FCC Rules.    Operation is subject 
to the following two conditions: 
1.  This device may not cause harmful interference, and 
2.  This device must accept any interference received, including 

interference that may cause undesired operation. 

 

Summary of Contents for ER-5397P









Reviews: