Edison Autoslide Installation Manual Download | Manualshive

Page: 12 / 12

background image

12

Wiring

The 120V power cord is prewired inside the enclosure. To exit the enclosure, slice the concentric
‘boot’ at the base of the enclosure, disconnect the plug from the terminals, and thread the cord
through the boot. Reconnect the terminals. IMPORTANT:

Always

have the power disconnected

when adjusting any wiring on the system.

Wire the accessories and safety photoeyes to the terminals numbers as shown. Polarity is not
observed with these devices.

To power the track, connect the RED wire to terminal 7 and the GREEN wire to terminal 8.

Wall Button

Photoeye set

1 2 3 4 5 6

To 120V outlet

7 8

Wires exiting
track

red

green

«
...
10
11
12

Summary of Contents for Autoslide













Reviews:

No comments

Related manuals for Autoslide

Brand: Calimet Pages: 3

Brand: Tower Hobbies Pages: 16

Brand: tousek Pages: 48

DiGi Digidoor 6 S

Brand: Hydro Pages: 18

Brand: RADEMACHER Pages: 78

Brand: CAME Pages: 20

Brand: Homentry Pages: 16

Brand: GDS Pages: 11

Brand: Automatic Solutions Pages: 14

Brand: Automatic Pages: 36

Brand: Chamberlain Pages: 88

Brand: Chamberlain Pages: 180

Brand: Beninca Pages: 24

Brand: Roger Technology Pages: 16

Brand: FAAC Pages: 4

Brand: Phoenix Doors Pages: 13

MAX SUPER ARM 1300

Brand: Maximum Controls Pages: 15

Brand: Daspi Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands