background image

© Edwards Limited 2009. All rights reserved. 

Page 5

Edwards and the Edwards logo are trademarks of Edwards Limited.

INSTALLATION

A505-71-880 Issue C

3

INSTALLATION

3.1

Safety

z

A suitably trained and supervised technician must install the Silencer.

z

Ensure that the installation technician is familiar with and complies with the safety procedures which relate 
to the products processed by the pumping system. Wear the appropriate safety-clothing when you come into 
contact with contaminated components. Dismantle and clean contaminated components inside a fume-
cupboard.

z

If the GV pump has been in operation, vent and purge the process system, then shut down the GV pump and 
allow it to cool to a safe temperature before you start installation.

z

Disconnect the GV pump and the other components in the process system from the electrical supply so that 
they cannot be operated accidentally.

z

Use suitable lifting equipment to move the Silencer.

3.2

Unpack and inspect

Remove all packing materials and protective coverings and inspect the Silencer. If the Silencer is damaged, notify 
your supplier and the carrier in writing within three days; state the Item Number of the Silencer, together with your 
order number and the supplier’s invoice number. Retain all packing materials for inspection. Do not install and use 
the Silencer if it is damaged.

Check that you have received the items listed in 

Table 1

. If any item is missing, notify your supplier in writing within 

three days. If the Silencer is not to be used immediately, store it in suitable conditions, as described in 

Section 4.1

.

WARNING

Obey the safety instructions given below and take note of appropriate precautions. If you do not, 
you can cause injury to people and damage to equipment.

Table 1 - Checklist of items

Qty Description 

Check 

(

)

1 Exhaust 

Silencer 

M8 bolts, nuts, plain and spring washers

ISO63 trapped ‘O’ ring

Summary of Contents for GV250

















Reviews: