Lighting Profile Setup & Battery Change: open the bottom cover (Fig.2)
Battery change: unplug the fault battery and replace it with the new battery. Noted that the battery plug only fit in one way.
VR1: adjust dimming brightness (from 5-50% of max brightness in either mode, clockwise to increase), minimum set is recommended.
VR2: adjust sensor range, can be adjusted from 10 - 50 ft, turn counterclockwise to decrease sensitivity range. (Fig.5)
Notes: increasing dimming brightness & sensitivity may reduce the length of illumination period, especially during winter time
Installation Guidelines
1. Securely mount the unit on the light pole or wall, adjust the light head direction and angles based on your need (Fig.4, 6)
2. Solar Panel must be mounted in a non-obstructed position that allows at least 5-6 hours direct sunlight all year round. For most of the North
America projects, adjust the tilt of the solar panel at 20
°
- 45
°
degrees based on your actual location. If you are close to equator
’
s location, a flat
installation (light head is parallel to the ground) will be reasonable.
The solar panel can be pointed between east to west, but
definitely not to north
.
For northern hemisphere installations, a south-facing position is best and visa-versa for southern hemisphere installation.
Optional AUX Input DC power sources can be used as charging enhancement for poor sunlight location or balancing the solar panel direction
and lighting projection with conflict (Fig. 1) . Refer:
https://youtu.be/hDn5JWr_DPA
3. Solar Panel Maintenance: Use soft, wet cloth to clean the solar panel periodically (at least once a one year) to avoid energy output reduction
resulted from accumulated dust. Clean accumulated snow ASAP during snowing season.
Rev: 022020
ON/OFF
Main
Switch
AUX v solar panel: 15-
20V/10-30W
DC Charger: 15-20V/-2A
Recommend
to charge 1-2
days with
main switch in
OFF position
before lit up
light
blink
once
5 min Self
Calibration
5-10 sec
Motion
If
Yes
Light ON
Light OFF
No
5 min
Daytime?
Light On
Yes
Light
OFF
Light turns ON
When
nighttime
comes
Thank you for choosing eLEDing! Built an exclusive auto-compensation firmware as AI-SMART mode for critical weather and seasons.
This product is designed to provide long lasting superior illumination by using environment-friendly Solar-Hybrid, Lithium-based energy
technologies. US, European, China and international patents granted and pending worldwide. All rights reserved. Users must read this manual
before installation, comply with local standard and regulations of construction & electrical/electronic projects, follow the safety guidelines to
prevent any possible accidents, incident and/or injuries. Consult experienced contractor/installer and electrical technicians for assistance.
Push
Latching
Switch
No
One Step Setup (Just 1 Click! Refer Fig.1)
Default
Setting
Auto convert within
0-3hrs w/higher
power or dimming
saving profile
Higher brightness profile will less than 3hrs.
AI-SMART default profile
(
Jumper2 open
, Fig.2 & 3)
Dimming brightness
until dawn
Dimming brightness
until dawn
Full brightness
up to 3hrs
After 3 hours
come to full
brightness
SMART 2: Jumper2
closed, disable motion
sensing for fixed pre-set
illumination level 5-50%
of max brightness, refer
Fig 2, VR1
Exclusive SMART
illuminating saving
mode to support
when/where with
insufficient Sunlight
Motion
detected
Motion
detected
If low power
(20% left)
ON with full
brightness
Motion
Switch to
AUTO Mode
Light OFF
No
Yes
Yes
Full Charge
Back to AI-SMART Mode
NO
Critical Reserve
(10% left)
ON with half
brightness
Motion
Light OFF
No
Yes
Intelligence Power Management (IPM) system : monitor & auto adjust power consumption
AI-SMART Mode
If in the critical weather
12346 Valley Blvd, #A, El Monte, CA 91732 Phone Number: 1-877-579-3889 info@eesgi.com Web: www.eleding.com
After Full
Charge
EESGI guarantees this product to be free from defects in material &
workmanship for (2) year.
This warranty does not apply to damage from misuse or incorrect installation/
connection.
This warranty does not cover accessories, bulbs, batteries, high voltage
accidents, alterations, unauthorized use or repair, neglect, misuse, abuse,
damages or defects resulting from normal wear and tear (including chips,
fading scratches, abrasions or discoloration due to usage or sun exposure), or
failure to follow instructions for care and maintenance, fire, flood, and Acts of
God.
This warranty does not include liability for incidental or consequential
damages.
EESGI is not responsible for any damages in excess of the retail purchase
price of the product under any circumstances. The consumer is responsible
for the installation of, removal of, and reinstallation of the product.
Two Year Limited Warranty
eLEDing
®
/ EE 800W - AI series
Solar Powered LED Smart Area/Street/
/
Parking/Courtyard Lighting
