background image

GENERAL SAFETY

The “Eemax Home Advantage” heater is specifically designed to take in hot or cold water and 
heat it to temperatures suitable for normal domestic usage up to a maximum of 140 F(60 C). 
To obtain optimum performance and energy savings, the unit should be located as
near as possible to the point of use. “Thermostatic” models indicated by the letters TC after 
the model number, these models and only these, can be fed with pre-heated water and be 
used to boost temperature

The unit is supplied with ¾’’ quick connect/disconnect  type fittings.   Follow the instructions 
supplied by the manufacturer of the fittings that are supplied with this manual.

When removing and re-installing the cover make sure to use the ground screw provided.  There 
are a total of 5 screws that affix the cover to the unit.  If you are missing any call technical 
support at 1-800-543-6163.

Also, ensure that the pipes are clear of installation debris before fitting the heater.

THIS HEATER MUST HAVE

TWO DEDICATED INDEPENDENT 240V, 220V 

or 208V 

CIRCUITS, USING CORRECTLY RATED WIRES AND CIRCUIT 

BREAKERS. PER UL 499, 18.4 THE RATING OF THE BRANCH-CIRCUIT 

OVERCURRENT PROTECTIVE DEVICE SHALL BE 150% OF THE RATING 

OF THE PRODUCT.  

DO NOT USE SPACE SAVING BREAKERS

.

WARNING

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE
CAN CAUSE

DEATH, SERIOUS BODILY INJURY OR PROPERTY DAMAGE

. REFER TO 

THIS MANUAL FOR ASSISTANCE OR CONSULT THE LOCAL ELECTRIC UTILITY FOR 
FURTHER INFORMATION.

FAILURE TO 

GROUND

THE SYSTEM MAY RESULT IN DEATH OR SERIOUS INJURY.

WARNING

WARNING

WATER HEATERS EQUIPPED FOR ONE VOLTAGE ONLY:  

THIS WATER HEATER MAY BE

EQUIPPED FOR ONE VOLTAGE TYPE ONLY: CHECK THE RATING PLATE ON THE FRONT 
COVER OF UNIT FOR THE CORRECT VOLTAGE. DO NOT USE THIS WATER HEATER WITH
ANY OTHER VOLTAGE OTHER THAN THE ONE SHOWN ON THE MODEL RATING PLATE.
FAILURE TO USE THE CORRECT VOLTAGE CAN CAUSE PROBLEMS WHICH CAN RESULT 
IN DEATH, SERIOUS BODILY INJURY, OR PROPERTY DAMAGE. IF YOU HAVE ANY 
QUESTIONS OR DOUBTS CONSULT EEMAX OR YOUR ELECTRIC COMPANY.

WARNING

HAZARD OF ELECTRICAL SHOCK! BEFORE REMOVING THE COVER OR SERVICING THE 
WATER HEATER, MAKE SURE THE ELECTRICAL SUPPLY TO THE WATER HEATER IS 
TURNED “OFF”. FAILURE TO DO THIS COULD RESULT IN

DEATH, SERIOUS BODILY INJURY,

OR PROPERTY DAMAGE

NOTE: UNIT HAS MULTIPLE ELECTRICAL CONNECTIONS.

2

THIS UNIT HAS MULTIPLE POWER SOURCES.  ENSURE TO DISCONNECT ALL POWER 

SUPPLIES BEFORE SERVICING 

Summary of Contents for SS015240TC












Reviews: