14
EN
door opening, then turn the Programme
Selection knob to Pump+Spin programme
and discharge the water in the machine.
Machine is in Rinse Hold mode
Spin symbol flashes and Pause symbol illuminates
when the machine is in Rinse Hold mode.
If you want to spin your laundry when the machine
is in this mode:
Adjust the spin speed and press Start / Pause
/ Cancel button. Pause symbol disappears and
Start symbol appears. Programme resumes,
discharges the water and spins the laundry.
If you only want to drain the water without spinning:
Just press Start / Pause / Cancel button. Pause
symbol disappears. Start symbol appears.
Programme resumes and discharges the water only.
End of programme
“End” appears on the display at the end of the
programme. Symbols of the programme steps
remain lit. Auxiliary function, spin speed and
temperature that were selected at the beginning
of
the programme remain selected.
end of each water intake hose where they are
connected to the tap. These filters prevent foreign
substances and dirt in the water to enter the
washing machine. Filters should be cleaned as
they do get dirty.
Close the taps. Remove the nuts of the water
intake hoses to access the filters on the water
intake valves. Clean them with an appropriate
brush. If the filters are too dirty, take them out
by means of pliers and clean them. Take out the
filters on the flat ends of the water intake hoses
together with the gaskets and clean thoroughly
under running water. Replace the gaskets and
filters carefully in their places and tighten the hose
nuts by hand.
Draining remaining water and
cleaning the pump filter
The filter system in your machine prevents solid
items such as buttons, coins and fabric fibers
clogging the pump impeller during discharge of
washing water. Thus, the water will be discharged
without any problem and the service life of the
pump will extend.
If the machine fails to drain water, the pump filter
is clogged. Filter must be cleaned whenever it
is clogged or in every 3 months. Water must be
drained off first to clean the pump filter.
In addition, prior to transporting the machine
(eg., when moving to another house) and in case
of freezing of the water, water may have to be
drained completely.
Foreign substances left in the pump filter may
damage your machine or may cause noise
problem.
In order to clean the dirty filter and discharge the
water:
Unplug the machine to cut off the supply power.
Temperature of the water inside the machine
may rise up to 90 ºC. To avoid burning risk,
filter must be cleaned after the water in the
machine cools down.
Open the filter cap.
If the filter cap is composed of two pieces, press
the tab on the filter cap downwards and pull
the piece out towards yourself.
5 Maintenance and cleaning
Service life of the product extends and frequently
faced problems decrease if cleaned at regular
intervals.
Cleaning the detergent drawer
Clean the detergent drawer at regular intervals
(every 4-5 washing cycles) as shown below
in order to prevent accumulation of powder
detergent in time.
Press the dotted point on the siphon in the
softener compartment and pull towards you until
the compartment is removed from the machine.
If more than normal amount of water and
softener mixture starts to gather in the softener
compartment, the siphon must
be cleaned.
Wash the detergent drawer and the siphon with
plenty of lukewarm water in a washbasin. Wear
protective gloves or use an appropriate brush
to
avoid touching of the residues in the drawer with
your skin when cleaning. Insert the drawer back
into its place after cleaning and make sure that it is
seated well.
Cleaning the water intake filters
There is a filter at the end of each water intake
valve at the rear of the machine and also at the
Your machine is equipped with
a “Standby Mode”
In case of not starting any programme or
waiting without making any other operation
when the machine is turned on by On/Off
button and while it is in selection step or if
no other operation is performed approximately
2 minutes after the programme you selected
has come to an end,your machine will
automatically switch to energy saving mode.
Display brightness will decrease. In case of
rotating the Programme Selection knob or
pressing any button, lights will restore to their
previous condition. This is not a fault.
