B
Dosierkammer-Deckel
h
abnehmen, Dosierkammer
g
, Pumpenkammer und Ausströmöffnung mit Reinigungsbürste
(Best.-Nr. 4009560) säubern. Anschließend das Pumpenrad wieder einsetzen und mit Pumpendeckel schließen. Den Filter
wieder im Aquarium einsetzen und über den Netzstecker in Betrieb nehmen.
a
Power-LED-Lampe
b
Lampenhalter
c
Steckverbindung
d
Kabelführung
e
Netzgerät.
Power-LED-Lampe
A
Lampenhalter
b
in die Führungslöcher auf der Rückseite des Filters einschieben.
B
Power-LED-Lampe
a
in den Lampenhalter einklippsen und Lampe mittig ausrichten.
Achtung: Pfeilrichtung beachten, da sonst keine Funktion.
C
Netzgerät
e
und Lampenhalter
b
mit der Steckverbindung
c
verbinden und Netzkabel des Innenfilters über die Ka-
belführung
d
führen. Netzgerät einstecken und Lampe mit Kippschalter einschalten.
D
Wir empfehlen, die Lampe ca. 8 cm über der Wasseroberfläche zu installieren. So wird die optimale Ausleuchtung er-
reicht.
F Montage / Inbetriebnahme
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING
–
To guard against injury, basic safety precautions should be observed, including the following.
a)
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b)
DANGER
–
To avoid possible electric shock, special care should be taken since water is employed in the use of
aquarium equipment. For each of the following situations, do not attempt repairs by yourself; return the appliance to
an authorized service facility for service or discard the appliance.
1)
If the appliance falls into the water,
DON’T
reach for it! First unplug it and then retrieve it. If electrical compo-
nents of the appliance get wet, unplug the appliance immediately. (Non-immersible equipment only)
2)
If the appliance shows any sign of abnormal water leakage, immediately unplug it from the power source.
(Immersible equipment only)
3)
Carefully examine the appliance after installation. It should not be plugged
in if there is water on parts not intended to be wet.
4)
Do not operate any appliance if it has a damaged cord or plug, or if it is
malfunctioning or has been dropped or damaged in any manner.
5)
To avoid the possibility of the appliance plug or receptacle getting wet,
position aquarium stand and tank to one side of a wall-mounted recep-
rtacle to prevent water from dripping onto the receptacle or plug.
A ”drip loop”, shown in the figure, should be arranged by the user for
each cord connecting an aquarium appliance to a receptacle. The ”drip
loop” is that part of the cord below the level of the receptacle, or the
connector if an extension cord is used, to prevent water traveling along
the cord and coming in contact with the receptacle.
If the plug or socket does get wet,
DON’T
unplug the cord. Disconnect the fuse or circuit breaker that supplies
power to the appliance. Then unplug and examine for presence of water in the receptacle.
c)
Close supervision is necessary when any appliance is used by or near children.
USA
AQUARIUM
TANK
APPLIANCE
POWER
SUPPLY
CORD
DRIP
LOOP
Summary of Contents for 6500 000
