26
USER MANUAL
MAGIC 500 PLUS ULTRASOUND UNIT
T +49 7461 96 580 0 | F + 49 7461 96 580 90 | export@eickemeyer.com | www.eickemeyer.com
7. GENERAL MEASUREMENT
7.1 Distance Measurement
1. In B, B / B mode, freeze the desired image, press direction keys
to move the cursor to “Measure” position of display area.
2. Press
key, the measurement methods are shown in the lower left of the screen, press direction keys
to choose
“1. Distance”, press
key again, the cursor will show “+”.
3. Press direction keys to move the “+” mark to desired position, press
key to set the “+” mark position as the starting
point of the measurement.
4. Press direction keys to move the “+” mark to the end point of the measurement. A lighted dotted line appears between the
starting point and the end point as the dashed locus of the measurement. The measured value is automatically displayed
at the built-in mark“+: ----mm” on the right side of the screen.
5. Press
key to exchange the starting and end point of the measurement.
6. Press
key to fi nish the fi rst measurement.
7. Press
key again, repeat the steps 3 – 6 to complete the multi-group data measurement.
8. Press
key to quit the measurement status.
9. Press direction keys
to choose “Clear” and press
key to clear all marks and data.
10. Press
key to return the real-time status.
7.2 Circumference / Area / Volume Measurement
Circumference / Area / Volume Measurement with Ellipse Method
1. In B, B / B mode, freeze the desired image, press direction keys
to move the cursor to “Measure” position of display
area.
2. Press
key, the measurement methods are shown in the lower left of the screen, press direction keys
to choose
“2. Ellipse”, press
key again, the cursor will show “+”.
3. Press direction keys to move the “+” mark to desired position, press
key to set the “+” mark position as the starting
point of the measurement.
4. Press direction keys to move the “+” mark to the end point of the measurement, at the same time the elliptic curve
appears.
5. Press
key, the “- +” mark appears on the lower right of the image. Hold down
or
key to change the minor axis of
the ellipse to satisfy the test area. The measured values are displayed at the built-in characters “C: ----mm, A: ----mm²,
V: ----cm³” on the right part of the screen automatically.
6. Press
key again to quit the minor axis status; Press
key to exchange the starting and end point.
7. Press
key to fi nish the fi rst measurement.
8. Press
key again, repeat the steps 3 – 7 to complete the multi-group data measurement.
9. Press
key to quit the measurement status.
10. Press direction keys
to choose “Clear” and press
key to clear all marks and data.
11. Press
key to return the real-time status.
Circumference / Area Measurement with Trace Method
1. In B, B / B mode, freeze the desired image, press direction keys
to move the cursor to “Measure” position of display area.
2. Press
key, the measurement methods are shown in the lower left of the screen, press direction keys
to choose
“3. Trace”, press
key again, the cursor will show “+”.
3. Press direction keys to move the “+” mark to desired position, press
key to set the “+” mark position as the start of the
measurement.
4. Press direction keys to move the “+” mark to the end point of the measurement. At the same time, a locus appears in the
direction of operation between the two measurement marks. The measured circumference value is displayed automatically
at the built-in mark “C: ----mm” on the right part of the screen. Press
key to display at the built-in mark “A: 0,0 mm²”
the value of the measured area formed by measurement line enclosure.
5. Press
key again, repeat the steps 3 – 4 to complete the multi-group data measurement.
