GB
- 17 -
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Servicing
Danger! Always ensure that the machine is
not connected to the mains supply before
you start any servicing work.
•
In the following: One cycle means one raising
and lowering movement of a load. Periodic
inspection means an inspection after 100 cy-
cles.
•
Test periodically that the limit switches on
the cable hoist are in correct working order.
Conduct this test as follows: When the cable
has reached the maximum height, the lever
on the automatic stopping mechanism (5) will
be actuated. The motor (14) must then stop.
(Test without a load).
When the steel cable (6) has been unwound
as far as possible, the lever for the maximum
cable length (4) will be actuated. The motor
(14) must then stop.
•
Inspect the mains cable (12) and the control
cable (13) periodically.
•
The steel cable (6) and return roller (15) must
be greased every 200 cycles.
•
A check must be made every 30 cycles, as
shown in Fig. 4, to find whether the entire
steel cable (6) is in good condition. If it is da-
maged, it must be replaced by a steel cable
of the type specified in the technical data.
•
Check every 1000 cycles whether the screws
for the fastening bars (1) and return roller (15)
are properly tightened.
•
Check every 1000 cycles whether the hooks
(8/16) and return roller (15) are in good condi-
tion.
•
Lubricate the cable, chain, gear unit, bearings
and hooks regularly.
•
Check wearing parts after every 1000 cycles,
e.g.: cable, chain, hooks, belts and brake
linings.
•
Check before using the cable hoist whether
the Emergency Stop switch (9) and pushbut-
tons (10) are in perfect working order.
•
Check the braking system every 1000 cycles.
If the motor (14) makes any unusual noises or
cannot raise the rated load, it is possible that
the braking system requires an overhaul:
- Replace damaged or worn parts and keep
the service documentation relating to this in a
safe place.
- Please contact an authorized service center
for any unscheduled maintenance work.
•
Have your electric tools repaired only by a
qualified electrician.
8.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
9. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council o
ffi
ces.
Anl_TC_EH_250_SPK9.indb 17
16.11.2017 15:42:13
https://tm.by
Интернет
-
магазин
TM.by
Summary of Contents for 22.551.30
