GB
- 24 -
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The fol-
lowing hazards may arise in connection with
the equipment‘s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is applied.
Warning!
This equipment generates an electromag-
netic
fi
eld during operation. Under certain
circumstances this
fi
eld may actively or pas-
sively impede medical implants. To reduce
the risk of serious or fatal injuries, we recom-
mend persons with medical implants to con-
sult their doctor and the manufacturer of the
medical implant prior to using the equipment.
5. Before starting the equipment
The lawn mower is delivered partly assembled.
The push bar and the grass basket must be as-
sembled before using the lawn mower. Follow the
instructions step by step and refer to the pictures
when assembling.
Important!
Required assembly parts (screws,
cable guides, etc.) or functional parts (e.g. plugs,
wrenches, etc.) can be found in the molded parts
of the packaging or on the equipment.
The cable for the electrical connection of the mo-
tor and switching bar is located on the left-hand
teeth of the handlebar adjustment facility (Fig.
3). Take care to ensure that this is not damaged
during assembly.
Fitting the push bar
Use the quick-tightening screws (Fig. 2/Item 16)
to fasten the push bar (Fig. 4/Item 13) to the teeth
of the handlebar adjustment facility. If necessary,
turn the quick-tightening screw back su
ffi
ciently
on the thread so that the quick-release lever (Fig.
4/Item 16a) can then still be
fl
ipped down towards
the back.
You can adjust the angle of the long handle as a
whole by
fl
ipping up the two quick-release levers
(Fig. 5/Item 16a), with three settings available
for the angle (Fig. 5). Only these three positions
are available. As you do this, make sure that both
sides are set to the same position. To secure the
push bar again,
fl
ip the two quick-release levers
back into the closed position.
You can adjust the angle of the upper push bar
(Fig. 6a) by
fl
ipping up the two upper quick-re-
lease levers (Fig. 6/Item 16a), with three settings
available for the angle. As you do this, make sure
that both sides are set to the same position. To
secure the push bar again,
fl
ip the two quick-
release levers back into the closed position.
Fitting the catch basket
Press the carry-handle (Fig. 7/Item 5b) onto the
top part of the housing of the catch basket. During
assembly, make sure that there is an audible click.
Before you
fi
t the catch basket you must ensure
that the motor is switched o
ff
and the blade is not
rotating. Ejector
fl
ap (Fig .8/Item 7) with one hand.
Using the other hand, grab onto the basket by the
handle and hang it in from the top.
Filling level indicator of the grass collector
The grass collector is equipped with a
fi
lling level
indicator (Fig. 9/Item 12). which is opened by the
air
fl
ow that the lawn mower generates during ope-
ration. If the
fl
ap closes during mowing, the grass
collecting device is full and must be emptied. To
ensure the proper functioning of the
fi
lling level
indicator, the holes under the
fl
ap must always be
kept clean and passable.
Adjusting the cutting height
Caution!
Adjust the cutting height only when the machine
has been switched o
ff
and the safety plug has
been pulled out.
The cutting height is adjusted as follows (see Fig.
10):
1. Push the lever (7) outwards.
2. Set the lever (7) to the desired cutting height.
3. Release the lever (7) and check that it is se-
curely seated in the lock.
Reading o
ff
the cutting height
The cutting height can be set between 25-75 mm
in 6 intervals, and can be read o
ff
on the scale.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check,
fi
rst switch o
ff
the motor and pull out the
safety plug.
Anl_GE_CM_36_37_Li_SPK7.indb 24
Anl_GE_CM_36_37_Li_SPK7.indb 24
26.04.2021 08:29:37
26.04.2021 08:29:37
