GB
15
Power class:
G1
Max. temperature:
40°C
Max. altitude (above mean sea level):
1000 m
Spark plug:
NGK BPR6ES; Champion F7RTC
Operating mode S1 (continuous operation)
The machine can be continuously operated with the
quoted power output.
Operating mode S2 (temporary operation)
The machine may be temporarily operated with the
quoted power output. Afterwards the machine must
be stopped for a while to prevent it from overheating.
5. Before putting the machine into
operation
5.1 Assembly
5.1.1 Fitting the wheels (Fig. 6)
First place the screw (Item 26) through the washer
(Item 24) and then through the wheel (Item 14) and
the wheel hub (Item 25). Then push it through the
hole in the frame and secure it with a nut (Item 23).
5.1.2 Fitting the feet (Fig. 7)
Hold the foot (Item 17) against the frame as shown in
Figure 7. First place the screw (Item 18) through a
bent washer (Item 19), then through the hole in the
frame and the hole in the foot (Item 17) and secure it
with a nut (Item 22).
5.1.3 Fitting the push bar (Fig. 8/9)
First place the screw (Item 18) through the push bar
holder (Item 16), then through the hole in the frame
and secure it with a bent washer (Item 19) and a nut
(Item 22), as shown in Figure 8.
Insert the push bar (Item 15) into the two guides in the
push bar holder (Item 16) and then secure it with a
screw (Item 20), a nut (Item 22) and two washers
(Item 21), one on the left and one on the right, as
shown in Figure 9.
5.2 Electrical safety:
앬
Electric supply cables and connected equipment
must be in perfect condition.
앬
The generator is to be operated only with
equipment whose voltage specifications conform
with the generator's output voltage.
앬
Never connect the generator to the power supply
(socket-outlet).
앬
Keep the cable length to the consumer as short
as possible.
5.3 Environmental protection
앬
Dispose of soiled maintenance material and
operating materials at the appropriate collection
point.
앬
Recycle packaging material, metal and plastics.
5.4 Connecting to earth
The housing is allowed to be connected to earth in
order to discharge static electricity. To do this,
connect one end of a cable to the earth connection
on the generator (Fig. 3/4) and the other end to an
external earth (for example an earthing rod).
Important!
You must fill up with engine oil and fuel
before you can start the engine.
앬
Check the fuel level and top it up if necessary
앬
Make sure that the generator has sufficient
ventilation
앬
Make sure that the ignition cable is secured to
the spark plug
앬
Inspect the immediate vicinity of the generator
앬
Disconnect any electrical equipment which may
already be connected to the generator
6. Operation
6.1 Starting the engine
앬
Open the petrol cock (Fig. 2/Item 13) by turning it
down
앬
Set the ON/OFF switch (Fig. 1/Item 10) to the
“ON” position
앬
Move the choke lever (Fig. 2/ Item 11) to position
I Ø I.
앬
Start the engine with the reversing starter (Fig.
2/Item 12), by pulling forcefully on the handle. If
the engine does not start, pull the handle again.
Important.
Always pull the starter cable slowly
until you feel the initial resistance before you then
pull it quickly to start the engine. Do not allow the
starter cable to whip back of its own accord.
앬
Push the choke lever (Fig. 2/Item 11) back after
the engine has started.
Important!
When starting with the reserve starter, the motor may
recoil suddenly as it starts up, resulting in hand
injuries. Wear protective gloves when starting the
equipment.
Anleitung_RT_PG_3250_SPK1:_ 02.04.2008 11:29 Uhr Seite 15
