GB
- 15 -
in the corresponding recesses of the mount
inside the spraying unit. The needle will en-
gage audibly in the mount. If the needle fails
to engage in the mount and can be pulled
out again with ease, turn the needle slightly
clockwise or counter-clockwise and try again
to insert the needle.
12. Put on the twist cap such that the lever for set-
ting the spray width is in position on the twist
cap and extends through the corresponding
recess on the spraying unit.
13. Push the nozzle of the selected nozzle set
together with the inserted nozzle seal onto the
spraying unit. Be sure to align the nozzle such
that the edge on the side of the spraying unit
engages in the corresponding recess on the
side of the nozzle and that the inserted needle
is seated in the middle opening of the nozzle.
14. Place the air cap onto the spraying unit such
that the two side hooks of the air cap lie inside
the corresponding recesses on the side of the
nozzle.
15. Screw the union nut or the union nut with
adjusting ring clockwise onto the spraying
unit. Take care when screwing on the union
nut with adjusting ring that the two caps are
seated in the recesses of the adjusting ring,
otherwise it will not be possible to adjust the
spray pattern with the help of the adjusting
ring.
8.4 Cleaning the motor unit
1. Remove the mains plug from the power so-
cket before beginning with any cleaning.
2. If applicable, remove the spraying unit (9/11)
from the motor unit (2) as described in the
section “Attaching/replacing the spraying unit”.
3. Wipe the outside of the motor unit with a dry
cloth or with a cloth that has been slightly
dampened and well wrung out. Make sure that
no liquid gets inside the motor unit.
8.5 Replacing the air
fi
lter
Important! Risk of damage!
Improper handling of the
fi
ne paint sprayer could
result in damage.
•
Never use the fine paint sprayer without an air
filter. Without an air filter, dirt and dust will be
drawn in and have an effect on the spraying
results.
•
Check the air filter at regular intervals for dirt,
dust and similar.
•
Check the air filter particularly if you notice
a drop in spraying performance or if you can
see that dust is collecting at the ventilation
openings.
•
Change the air filter if it is heavily soiled.
The air
fi
lter protects against building dust and
similar, and it can be cleaned several times before
it needs to be replaced. You should try therefore
to clean the air
fi
lter before replacing it unneces-
sarily.
The air
fi
lter can be cleaned in various ways:
•
With the filter cover in place: clean the air filter
with a vacuum cleaner. Alternatively:
•
remove the filter cover and take out the air
filter as described below. Then tap or blow the
dust layers off the air filter and re-insert the
cleaned air filter as described below.
1. Remove the four screws holding the
fi
lter
cover by unscrewing them counter-clockwise
(see Fig. L).
2. Remove
the
fi
lter cover from the motor unit
towards the back.
3. Remove the air
fi
lter and replace it with a mat-
ching replacement
fi
lter.
4. Place
the
fi
lter cover back on the motor unit.
5. Fasten
the
fi
lter cover on the motor unit
with the help of the four previously removed
screws.
8.6 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.7 Ordering spare parts and accessories
Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Tip! For good results we
recommend high-quality ac-
cessories from
!
www.kwb.eu
welcome@kwb.eu
Anl_BT_FSS_500_EX_UK.indb 15
Anl_BT_FSS_500_EX_UK.indb 15
05.10.2021 12:45:33
05.10.2021 12:45:33
