GB
GB
- 20 -
Using the grass trimmer as an edge trimmer
(Fig. 11)
To cut the edges of lawns and flower beds, the
grass trimmer can be converted as follows:
•
Pull the lock in the direction of the arrow (Fig.
11/Item 10).
•
With the lock pulled, turn the motor head
through 90°. (It can be turned 90° to the left
and to the right.)
•
The height adjustment works as described in
section 5.3.
•
Now you have converted the grass trimmer to
an edge trimmer for cutting the lawn vertically.
7. Replacing the power cable
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
•
Use a brush to remove deposits from the
safety guard.
8.2 Replacing the line spool
Important! Make sure that you pull out the
power plug before replacing the line spool!
•
Press the sides of the spool cover as shown
and remove the cover (Figure 12b).
•
Remove the empty line spool.
•
There is a spare line spool in the additional
handle. To take it out, proceed as follows:
Press the lever (Fig. 12a/Item B) in the direc-
tion of the arrow and pull the spare line spool
out of the holder.
•
Thread the end of the line from the new line
spool through the eyelet in the spool mount
(Fig. 12c) and allow approx. 10 cm of line to
project.
•
Fit the spool cover back in the spool mount.
•
When you start the equipment again the line
will be cut to the perfect length automatically.
Important! Bits of the nylon line could cause
injury when flung out!
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Spare line spool Art. no.: 34.056.90
9. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offices.
Anl_GC_ET_4025_4526_SPK7.indb 20
18.12.13 11:40
Summary of Contents for GC-ET 4025
