GB
- 25 -
or fatal injuries, we recommend persons with
medical implants to consult their doctor and the
manufacturer of the medical implant prior to using
the equipment.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
The lawn mower is delivered unassembled. The
complete push bar, the rear wheels and the grass
basket must be assembled before using the lawn
mower. Follow the operating instructions step-
by-step and use the pictures provided as a visual
guide to easily assemble the equipment.
Fitting the wheels (Figures 3a, b and 4)
Take the rear wheels (Figure 2/Item11) and mount
them on the axle as shown in Figure 3a. Then
slide the washer (Figure 2/Item 23) onto the axle
and fasten all parts with the supplied split pin
(Figure 2/Item 22) as shown in Figure 3b. Finally,
press the wheel caps (Figure 2/Item 10) onto the
wheels (Figure 4).
Mounting the push bar (Fig. 5 to 10)
First take the spring (Figure 2/Item 16) and the
handlebar mount (Figure 2/Item 12) and mount
them on the relevant axle (Figure 5). Now insert
the push bar holder (Figure 2/Item 3) into the
handlebar mount (Figure 2/Item 12) and secure
with the quick clamping function (Figure 2/Item
17) (Figure 6). Important. Do not forget to
fi
t the
holder for the cable strain-relief clip (Figure 2/Item
15) and the strain-relief clip (Figure 2/Item 9) on
the top push bar
fi
rst.
The top push bar (Figure 1/Item 2) must be pu-
shed onto the push bar holders (Figure 2/Item 3)
and secured as shown above in Figure 9. Then at-
tach the power cable to the push bar (Fig. 10/Item
18) using the cable clips (Fig. 2/Item 18). Now you
can select the push bar height in three steps from
93.5 to 115.5 cm (Figure 7/Item A).
Important.
The handle height may only be adjusted within
the marked range.
•
Press in the long handle and secure in the
desired position using the quick clamping
function (Figure 7/Item B)
Important.
Always set the identical handle height on both
sides.
•
Use the cable clips to align the cable in ac-
cordance with the long handle (Figure 10/
Item 18)
Mounting the grass basket
(see Figs. 11 to 13)
First, plug the left (Fig. 2/Item 21) and right (Fig. 2/
Item 20) part of the housing together as shown in
Figure 11. Then plug the top part of the housing
(Fig. 2/Item 19) onto the already mounted parts
(Figure 12). Before you
fi
t the grass basket you
must ensure that the motor is switched o
ff
and the
blade is not rotating. Lift the ejector
fl
ap (Fig. 13 /
Item A) with one hand. With the other hand, hold
the grass basket by the handle and hook it in from
above (Fig. 13).
Filling level indicator of the grass collector
The grass collector is equipped with a
fi
lling level
indicator (Fig. 2/Item 24) which is opened by the
air current that the lawn mower generates during
operation. If the
fl
ap closes during mowing, the
grass collecting device is full and must be emp-
tied. To ensure the proper functioning of the
fi
lling
level indicator, the holes under the
fl
ap must be
kept clean and open.
Using the mulching adapter (Fig. 14, not in-
cluded with 34.002.94):
In mulching mode the cuttings are shredded in
the enclosed mower housing and then spread
back onto the lawn. It is not necessary to gather
and dispose of the grass.
Important:
Mulching is only possible if the lawn is
relatively short.
Important!
Insert the mulching blade only when the engine is
switched o
ff
and the power plug has been pulled
out.
To use the mulching function, disconnect the
grass box, slide the mulching adaptor (Fig. 14/
Item 25) into the ejector opening and close the
ejector
fl
ap.
Anl_GE_EM_1536_HW_M_SPK7.indb 25
Anl_GE_EM_1536_HW_M_SPK7.indb 25
31.07.13 15:48
31.07.13 15:48
