GB
- 21 -
The wet and dry grinder is equipped with a dry
grinding wheel and a wet grinding wheel. Please
note that rough grinding is always performed with
the dry grinding wheel. Carry out
fi
ne grinding
jobs with the wet grinding wheel, applying only
slight pressure. The wet and dry grinder was
developed for the machining and sharpening of
knives, scissors, chisels and tools with a blade.
The machine is allowed to be used only for its
intended purpose! Even when the equipment is
used as prescribed it is still impossible to elimina-
te certain residual risk factors. The following ha-
zards may arise in connection with the machine‘s
construction and layout:
•
Contact with the grinding wheel where it is not
covered.
•
Catapulting of parts from out of damaged
grinding wheels.
•
Catapulting of workpieces and parts of work-
pieces.
•
Damage to hearing if essential ear-muffs are
not used.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or indust-
rial businesses or for equivalent purposes.
4. Technical data
Mains voltage: ........................220-240 V ~ 50 Hz
Power rating: ......... S1 170 W | S2 30 min 250 W
Idle speed n0: .....................................2980 min
-1
Protection class ................................................. I
Protection type: ............................................IPX0
Weight: ......................................... approx. 9.5 kg
Dry grinding wheel:
Grinding wheel ø max. ............................ 157 mm
Grinding wheel ø min.: ........................... 127 mm
Grinding wheel diameter: ....................... 150 mm
Grinding wheel thickness: ........................ 20 mm
Grinding wheel hole diameter: ................. 32 mm
Speed: ................................................2980 min
-1
Circumferential speed: ...........................23.4 m/s
Grinding wheel grit size: ................................K36
Wet grinding wheel:
Grinding wheel ø max.: .......................... 207 mm
Grinding wheel ø min.: ........................... 173 mm
Grinding wheel diameter: ....................... 200 mm
Grinding wheel thickness: ........................ 40 mm
Grinding wheel hole diameter: ................. 20 mm
Speed: ..................................................134 min
-1
Circumferential speed: .............................1.4 m/s
Grinding wheel grit size: ..............................K200
Load factor:
A load factor of S2 30 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (250 W)
for no longer than the time stipulated on the spe-
ci
fi
cations label (30 minutes ON period). If you fail
to observe this time limit the motor will overheat.
During the OFF period the motor will cool again to
its starting temperature.
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 62841.
Operation
L
pA
sound pressure level ..................... 79.4 dB(A)
K
pA
uncertainty ........................................ 3 dB(A)
L
WA
sound power level ....................... 92.4 dB(A)
K
WA
uncertainty ........................................ 3 dB(A)
Wear ear-mu
ff
s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
speci
fi
ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Anl_TC_WD_200_150_SPK9.indb 21
Anl_TC_WD_200_150_SPK9.indb 21
23.06.2020 15:30:18
23.06.2020 15:30:18
