TECNOEKA Srl ______________________________________________________________ use and instruction manual
page 6 __________________________________________________________________________________________
4.
4.
4.
4. Instructions for the installer
Instructions for the installer
Instructions for the installer
Instructions for the installer
The following instructions are aimed at the qualified installer, to ensure that he carries out the
installation, adjustment and maintenance operations as correctly as possible and according to
current legal regulations. Any operation must be performed with electrical power cut to the
appliance. Before using the appliance, carefully remove the special adhesive film protecting the
parts in stainless steel. Do not leave any glue residues on the surfaces. If necessary, remove
them at once, with an appropriate solvent.
Positioning
Positioning
Positioning
Positioning - Position the appliance perfectly horizontally on a table or similar support (the table
or support must be at least 85 cm above the floor). Position it at a distance of not less than 10
cm from the side and rear walls, to enable natural ventilating air to circulate freely around it.
The appliance is ventilated through specific openings on the metal walls of the outer housing ,
and ensures efficiency and long-life. For this reason it is strictly forbidden to obstruct these
ventilation openings, even partially or for short periods. Failure to observe this specific
Failure to observe this specific
Failure to observe this specific
Failure to observe this specific
prohibition releases the manufacturer of the appliance from all responsibility and immediately
prohibition releases the manufacturer of the appliance from all responsibility and immediately
prohibition releases the manufacturer of the appliance from all responsibility and immediately
prohibition releases the manufacturer of the appliance from all responsibility and immediately
voids any guarantee rights for the said appliance,
voids any guarantee rights for the said appliance,
voids any guarantee rights for the said appliance,
voids any guarantee rights for the said appliance, because its constructive conformity has been
voluntarily compromised. Furthermore, the appliance is not suitable for embedding and for
grouped positioning with other identical appliances.
Electrical connection
Electrical connection
Electrical connection
Electrical connection - The appliance must be connected to the electrical mains according to
current legal regulations. Before making the connection, make sure of the following:
-
the voltage and frequency values of the power supply system match the values on the
"technical data" plate affixed on the appliance;
-
the limiting valve and the system are able to support the appliance's load (see the
"technical data" plate);
-
the power sup
the power sup
the power sup
the power supply system has an adequate earth connection according to current legal
ply system has an adequate earth connection according to current legal
ply system has an adequate earth connection according to current legal
ply system has an adequate earth connection according to current legal
regulations;
regulations;
regulations;
regulations;
-
a omnipolar switch with minimum between-contacts aperture of the overvoltage
category III (4000 V), sized to the load and conforming to current legal regulations, is
fitted between the appliance and the mains in the direct connection to the mains;
-
the omnipolar switch used for connection is easy to reach when the appliance is
installed;
-
the yellow/green earth wire is not interrupted by the switch;
the yellow/green earth wire is not interrupted by the switch;
the yellow/green earth wire is not interrupted by the switch;
the yellow/green earth wire is not interrupted by the switch;
-
the power supply, when the appliance is operating, must not deviate from the rated
voltage value by ±10%.
-
make sure that after inserting the power supply cord into the terminal block it does not
come into contact with any of the cooking range's hot parts.
-
if the supply cable is dama
if the supply cable is dama
if the supply cable is dama
if the supply cable is damaged then it must be replaced by the manufacturer or by your
ged then it must be replaced by the manufacturer or by your
ged then it must be replaced by the manufacturer or by your
ged then it must be replaced by the manufacturer or by your
technical support or by a qualified person to avoid any risk
technical support or by a qualified person to avoid any risk
technical support or by a qualified person to avoid any risk
technical support or by a qualified person to avoid any risk
Connection to the water mains
Connection to the water mains
Connection to the water mains
Connection to the water mains - The appliance must be fed with softened drinking water, with
hardness from 0.5°F to 5°F (it is obligatory to use a softener to reduce the formation of lime
inside the cooking chamber) and pressure in the range from 150 to 250 kPa (1.5 - 2.5 bar).
Connection to the water mains should be made through the threaded 3/4" solenoid-valve on
the rear of the appliance, fitting in between a mechanical filter and an on/off tap (before you
connect the filter, allow a certain quantity of water to flow out in order to drain any waste from
the pipe).
