background image

16 

 

 

Auxiliary power micro 

card overtemperature  

exceeded the 

temperature of 75°C 

Overtemperature above 75°C 
on the auxiliary power micro 
card 

Oven operation 
disabled 

Contact a skilled 
technician 

 
7 Possible errors 

Information on faulty oven operation without disabling it 

Type of error 

Error cause

 

Effect 

Corrective action 

 

Blackout 

the oven was off from 

xx:xx to yy:yy 

Power cut off for a period of 
time during the cooking cycle  

 

The screen displays 
the type of error. The 
oven continues 
working 

The oven automatically 
resumes the cooking cycle 
when the power supply is 
restored 

 

Display card 

overtemperature 

exceeded the 

temperature of 60°C 

Overtemperature above 60°C 
on the display card 

The screen displays 
the type of error. The 
oven continues 
working  

Contact a skilled 
technician 

 

Main power micro card 

overtemperature  

temperature of 60°C 

exceeded 

Overtemperature above 60°C 
on the main power micro card 

The screen displays 
the type of error. The 
oven continues 
working 

Contact a skilled 
technician 

 

Auxiliary power micro 

card overtemperature  

temperature of 60°C 

exceeded 

Overtemperature above 60°C 
on the auxiliary power micro 
card 

The screen displays 
the type of error. The 
oven continues 
working 

Contact a skilled 
technician 

 

Humidification 

malfunction, cannot 

reach the desired 

humidity. 

Insufficient humidity in the 
cooking chamber  

The screen displays 
the type of error. The 
oven continues 
working 

Contact a skilled 
technician 

Summary of Contents for MILLENIAL MKF 1011 CTS





















Reviews: