background image

20

10.2.2

When not in use, it should be parked in a dry and ventilated garage to prevent

the sun and rain, and please note:

1 Turn off the electric lock, cut off the power and unplug the power plug;

2 After pulling up the stationary truck, the front and rear wheels should be well

parked.

3 In case of long-term disuse, the battery should be replenished every 15 days.

10.3 Check before Using

10.3.1

If the new vehicle is damaged during transportation, please do not put it into use and

contact the supplier in time for proper treatment.

10.3.2

New vehicles have been equipped with lubricating oil and hydraulic oil in the fuel

tank.

10.3.3

Storage battery for the moving vehicle. The battery has been charged at the factory. If

the factory is long, the power may be low. Attention should be paid to the display of the
electric meter before use. When the electric meter is shown to the last two bars of warning,
it must be charged immediately. Open the battery cover every day before use or before
charging. Check the level. If the level is too low, distilled water should be added before
charging. See (battery charging and maintenance) for details.

10.4 Safe Operation

10.4.1

Requirements for drivers: the vehicle must be operated by trained personnel;

10.4.2 Rights, obligations and duties of the driver:

the driver must clarify his rights and

obligations and have been trained in the operation of the vehicle; Be familiar with the

Summary of Contents for EP18D Series





























Reviews: