background image

   
DK50 4VR/50

 

       

 

04/2018 

- 7 -   

NP-DK50 4VR50-11_04-2018 

6.2. 

Optional accessories 

 
Products may be equipped with optional accessories that are not included with the basic product 
and must be ordered separately: 
 
Filter regulator / set 603022106-000 / 

The filter regulator filters out impurities in the compressed air down to a size 
of 5 

m. The use of this accessory on a compressor without a dryer partially 

reduces  moisture  content  in  the  supplied  compressed  air.  Filtered 
compressed  air  is  suitable  for  use  anywhere  its  parameters  meet  the 
stipulated  requirements.  The  regulator  ensures  a  supply  of  output  air  at  a 
constant pressure (so long as the pressure value set on the regulator is not 
higher than the switching pressure set on the pressure switch). 
 
 

Regulator / set 603022104-000 / 
 

The regulator ensures a supply of output air at a constant pressure (so long 
as  the  pressure  value  set  on  the  regulator  is  not  higher  than  the  switching 
pressure set on the pressure switch). 
 
 
 
 
 
 
 

Automatic condensate drain / set 603013114-000 / 

The automatic condensate drain automatically drains condensate from the compressor's air tank based on a 
pre-set time interval. 
The drain automatically opens a solenoid valve at a pre-set time interval to drain condensate from the air 
tank. 

  A timer is used to set the time between actuation of the solenoid valve (approximately 30 minutes). 

  The time between actuations of the solenoid valve can be adjusted to a lower value if excessive amount 

of condensate is generated. 

 

-

 The TEST button (2) is used to check the actuation of the solenoid valve, and when pushed the 

solenoid valve should open (ON) and the time between actuations of the solenoid valve begins from this 
point.  

-

 The LED (1) lights up to signalize the valve is open(ON). 

 
 

 
 
 
 
 
 
 
 
 
 
 

 
 

 
 
 
 
 
 
 

1

Summary of Contents for DK50 4VR/50




























Reviews: