Quick Index
Settings
Steps
Pairing
Switch Rotating Direction
Upper and Lower Limits Setting
Adjust Limits
P1 (hold down 2s) →
Stop (hold down 2s)
Up + Down (hold down 2s)
Set upper limit
Up (hold down 2s) → Up + Stop (hold down 2s)
Adjusting the upper limit
Up + Stop (hold down 5s) → Up or Down → Up + Stop (hold down 2s)
Adjusting the lower limit
Down + Stop (hold down 5s) → Up or Down → Down + Stop (hold down 2s)
Acceleration setting
P2 → Up → Up
Deceleration setting
P2 → Down → Down
Set lower limit
Down (hold down 2s) → Down + Stop (hold down 2s)
P2 → Stop → Stop
5
Add / Remove Preferred Position
4
3
2
1
Jog Mode & Running Mode Switch
Pair / Unpair Additional Emitter
Up + Down (hold down 5s) → Stop
P2(a) → P2 (a) → P2(b)
P2(a) → P2 (a) → Stop (b) (hold down 2s)
P1 (hold down 2s) →
Stop (b) (hold down 2s)
6
7
8 Speed Regulation
Troubleshooting
Issues
Possible causes
Solution
The motor has
no response
emitter battery is low capacity
Replace battery
Out of radio control range
Try control within closer range
The emitter cann't
control single motor
Multiple motors are paired to the
same channel.
Pair single motor with emitter correctly
Try to use multi-channel emitters to control multi-motor
projects, ensure each channel to control one single motor
The motor doesn't run or starts
too slowly or make loud noise
The motor stops during the
up and down running
Connections are incorrect.
Check connections
Installation is improper or overload
The motor has reached the upper limit
or lower limit
Adjust the new upper limit or lower limit
Check installation or overload
Radio interference / shielding
Check antenna on motor is intact and exposed. Check for
possible source of radio interference.
Power failure or incorrect connection
Double check power and cable connections, follow wiring
instructions.
Battery in motor is depleted
Charge with the corresponding charger or solar panel
Please read following points of attention carefully before setting.
Setting Notice
Important Safety Instructions To Be Read Prior To Operation.
Essential Settings
The steps in factory mode must be completed to ensure proper operation.
1. Don’t operate motors when low voltage alarm.
2. Operation
：
①
The valid interval time of the buttons is within 10S, if there is no operation within 10S, the emitter
will exit the present setting.
②
The motor will jog and beep as hint, pls operate after the jog and beep.
3. Set the limit position
：
①
After the upper / lower limit setting, and the upper / lower limit positin can’t at the same position.
②
After the limit setting, with power off and memory function.
③
Limit delete will clear all limit memory.
④
It will exit limit setting when program there is no operation for 2 minutes.
4. If the emitter lost, please set up again with the new emitter.
5. One motor can store maximum 10 channels; after fully stored, if pair new channels, only the last one
will be covered circularly.
Button Instructions
Charger port
and solar panel
charging port
P1 button
P1
Functions of P1 button
1. Cycle Operation: Press P1 button once and every press the motor will run upward → stop → downward circulary.
2. Pairing or Pair / unpair Additional Emitter: Press P1 button for 2S, motor jog once, release button and long beep once, motor
is ready for pairing or pair / unpair additional emitter.
3. Radio Lock: Press and hold P1 button for 6S, the motor will jog twice, release button and beep twice, the motor enters radio
lock status, the motor won't receive any signal; press P1 button once to disable Radio Lock.
4. Switch Direction: Press and hold P1 button for 10S, the motor will jog 3 times, release button and beep 3 times, the running
direction of the motor has been changed.
5. Reset to Factory Mode: Press and hold P1 button for 14S, the motor will jog 4 times, release button and beep 4 times, the
motor has been reset to factory mode.At this point the motor will go into deep sleep. After entering deep sleep, the motor
can't be controlled. At this time, you need to press P1 button for 2S and then the motor turns to prompt to exit deep sleep.
* The operation is only valid when there is no limits. If the motor has already set the upper and lower limit, then
you can only switch direction by P1 button.
2 Switch Rotating Direction
(Optional)
+
UP
DOWN
If press UP, the motor runs downward, try below to switch direction
Press and hold UP and DOWN buttons simultaneously for 2S
(1 jog
and 1 beep
)
, the direction has been switched successfully.
* If within 10S, the motor doesn't receive STOP signal from the any emitter, it will exit the paring mode automatically.
1 Pairing
Factory mode
Press P1 button for 2S (1 jog ), release button and make a long noise,
within 10S, press STOP for 2S (2 jogs and 3 beeps ), the motor has
been paired successfully.
STOP
P1
→
P1
1
Add A Preferred Position
User mode
1 Set preferred position
P2
→
→
P2
STOP
STOP
Check both upper and lower limits are set. Operate the
product to desired preferred position. Press P2 (1 jog
and 1 beep), press STOP(1 jog and 1 beep), STOP
again (2 jogs and 3 beeps), the preferred position is set.
2 Remove preferred position
P2
→
→
P2
STOP
STOP
Press P2 (1 jog
and 1 beep
), press STOP (1 jog
and 1 beep
), STOP again(1 jog
and long beep
once
), the preferred position is deleted.
* In the normal running mode, if the motor is not at the preferred position, press STOP button longly, then the motor
will run directly from the current position to the preferred position ( apply for roller systems); In the jog mode, press
STOP button longly, firstly, the motor runs from the current position to the lower limit then to the preferred position
(apply for cord-lifting system).
Press UP for 2S, operate the motor to desired upper
position, press and hold UP and STOP buttons
simultaneously for 2S (2 jogs and 3 beeps), upper
limit is set.
3 Upper and Lower Limits Setting
1 Set upper limit
→
+
UP
UP
STOP
* If exit the limits setting status before you finish the limit setting, then the motor will take the previous limits if has;
After the limits have been set successfully, the motor will enter the user mode.
Press DOWN for 2S, operate the motor to desired
lower position, press and hold DOWN and STOP
buttons simultaneously for 2S (2 jogs and 3 beeps),
lower limit is set.
2 Set lower limit
→
DOWN DOWN
STOP
+
* After entering the limits fine tuning mode, the original
preferred position
will not be deleted; If there is no button
operation within 2 minutes, it will arrive within 2 minutes, and the motor will turn to prompt, and automatically exit
the route adjustment mode.
* When in jog mode, press UP or DOWN once, the motor will be jog running, if press more than 2 second, the motor
will be continously running.
2
Jog Mode & Running Mode Switch
→
DOWN
STOP
UP
+
Press and hold UP and DOWN buttons simultaneously for 5S (1 jog),
press STOP (
1 jog
and long beep once), switch to jog mode, If motor
jog twice and beep 3 times, switch to running mode.
3 Adjust Limits
1 Adjusting the upper limit
→
→
DOWN
UP
or
→
+
UP
STOP
+
UP
STOP
The new upper
limit position
Press and hold UP and STOP buttons for 5S (
1 jog
and long beep once), operate the product to desired new
upper limit position, press and hold UP and STOP buttons for 2S(2 jogs and 3 beeps), the new upper limit is
programmed successfully.
2 Adjusting the lower limit
Press and hold DOWN and STOP buttons for 5S (
1 jog
and long beep once), operate the product to desired
new lower limit position, press and hold DOWN and STOP buttons for 2S (2 jogs and 3 beeps), the new
lower limit is programmed successfully.
→
→
DOWN
UP
or
→
+
DOWN
STOP
+
DOWN
STOP
The new lower
limit position
P2
P2
→
→
P2(a)
P2(a)
P2
P2(b)
4 Pair / Unpair Additional Emitter
• Repeat same procedure will unpair additional emitter.
Press P2 (1 jog and 1 beep) and P2 (1 jog and 1 beep) on existing emitter,
press P2 on new emitter to add (2 jogs and 3 beeps), new emitter is paired
to the motor.
Method one
Press P2 (1 jog and 1 beep) and P2 (1 jog and 1 beep) on existing
emitter, press STOP on new emitter for 2S to add (2 jogs and 3
beeps), new emitter is paired to the motor.
Method two
P2
P2
→
→
P2(a)
P2(a)
STOP(b)
P1
→
P1
* (a) as existing emitter,(b) as new emitter to pair/unpair;
All the setting of the motor will be kept after addiing the new emitter.
• Repeat same procedure will unpair additional emitter.
Press P1 button for 2S (1 jog), release button and long beep once,
press STOP on new emitter for 2S to add (2 jogs and 3 beeps), new
emitter is paired to the motor.
Method three
STOP(b)
Press P2 (1 jog and 1 beep), UP (1 jog and 1 beep), UP again
(
2 jogs
and 1 beep), the motor running speed is accelerated.
→
→
P2
P2
UP
5 Speed Regulation
UP
1 Acceleration setting
* DM45LE/S does not have this function; If the motor no response, it has already been the Max. or Min speed;
The factory default is the fastest.
→
→
Press P2 (1 jog and 1 beep), DOWN (1 jog and 1 beep), DOWN
again (2 jogs and 1 beep), the motor running speed is decelerated.
P2
P2
DOWN
DOWN
2 Deceleration setting
-3-
-5-
-4-
Lithium Cell
3V
P2
P2
UP
LCD
STOP
DOWN
Channel
sel”
(P1+)
P2
Channel
selection“-”
(P1-)
