background image

 Rev. 4/11

User Instructions

©Elation Pr

o

fessionals®  -  www.elationlighting.com  - Event Bar Instruction Manual Page 2

  Event Bar         

                                         General Information

Unpacking: 

Thank you for purchasing the Event Bar by Elation Pro-

fessionals

®

. Every Event Bar has been thoroughly tested and has been 

shipped in perfect operating condition. Carefully check the shipping 
carton  for  damage  that  may  have  occurred  during  shipping.  If  the 
carton appears to be damaged, carefully inspect your fixture for any 
damage and be sure all equipment necessary to operate the unit has 
arrived intact. In the event damage has been found or parts are miss-
ing, please contact our toll free customer support number for further 
instructions. Please do not return this unit to your dealer without con-
tacting customer support first. 

Introduction: 

The Event Bar DMX intelligent LED fixture. The Event 

Bar has 3 DMX Modes; 12 Channel DMX Mode, 14 Channel Mode, and 
25 Channel Mode. The fixture three operating modes;  sound active 
mode, show mode or DMX controlled. The Event Bar can only be run 
as stand alone unit. 

For best results use fog or special effects smoke to 

enhance the light projections. 

Customer Support:

 Elation Professionals

®

 provides a toll free cus-

tomer support line, to provide help and to answer any question should 
you  encounter  problems  during  your  set  up  or  initial  operation.  You 
may also visit us on the web at www.elationlighting.com for any com-
ments or suggestions. Service Hours are Monday through Friday 9:00 
a.m. to 5:00 p.m. Pacific Standard Time.
 

Voice:   

(323) 582-3322

 

Fax: 

  

(323) 832-9142

 

E-mail:  

support@elationlighting.com

To purchase parts online visit http://parts.elationlighting.com

Warning! 

To prevent or reduce the risk of electrical shock or fire, do 

not expose this unit to rain or moisture. 

Warning! 

This may cause severe eye damage. Avoid looking directly 

into the light source at all times!

EVENT BAR

Summary of Contents for EVENT BAR











Reviews: