Multi-Data/Pak Instruction Manual Page 6
Speed Settings:
This setting adjusts the speed of the internal chase. The number of channels in
a chase can be adjusted between 1-72 channels. This chase can not be edited.
To change the chase speed, do the following:
1. Press and hold down the MENU button for three seconds.
2. When the LED Display begins to flash, tap the MENU button three times
to activate the SPEED settings. This will be indicated by SPXX flashing in
the LED Display.
3. Use the UP and DOWN buttons to select your desired chase speed. The
speed can be adjusted from 01 to 99. A setting of 01 is the fastest chase
speed at 1/10 of a second. A setting of 99 is the slowest chase speed at
every 10 seconds.
4. When you have made your selection, tap the MENU button twice to exit
this function and store your setting.
Channel Setting:
This setting allows you to change the starting DMX channel. To make changes
to this setting, do the following.
1. Press and hold down the MENU button for three seconds.
2. When the LED display begins to flash, be sure the DMX LED on the left
of LED display is flashing. If it is not flashing, use the UP and DOWN
buttons to select DMX mode. (See Mode Setting on page 5).
3. When you are in DMX mode, tap the MENU button once to activate the
DMX settings. This will be indicated by AXXX flashing in the LED display.
4. Use UP and DOWN buttons to select your desired DMX address. The
address can be set between 001 to 512. NOTE: ONLY 72 TOTAL
CHANNELS WILL OUTPUT STARTING WITH THE SET ADDRESS.
5. When you have made your selection, tap the MENU Button four times to
exit this function and store your setting.
Programming a BACK-UP Scene:
This functions allows you to program one scene ino the data pack's memory.
This scene can be recalled at any time. To program a scene, do the following:
1. With any DMX controller, program a scene using any of the available 72
channels..
2. Press and hold down the SCENE button for five seconds until "GOOD"
is displayed in the LED display.
3. To recall the scene, press the SCENE button at any time. "STOR" will be
displayed in the LED display indicating that the unit is running the stored
scene.
Features:
The Multi-Data/Pak is a universal signal converter that converts DMX and
MIDI to an Analog signal. This allows you to use your analog dimmer and
power packs with a DMX controller or MIDI sequencer. The unit can
convert up to 72 DMX channels. This unit may also be used as a 72
channel chaser. One scene can be stored into memory as an emergency
back up should your controller ever fail. This unit has built in memory in the
case that the unit's power is ever disconnected.
1
2
4
3
5
6
9
10
11
12
13
14
7 8
POWER
FUSE
MENU
MIDI IN
MIDI THRU
DMX IN
DMX IN
DMX OUT
DMX OUT
STORE
CHASE
8 8 8 8
Signal
DMX
HOLD
MIDI
MULTI-DATA/PAK
F1A 250V 5x20mm
Functions & Controls (Front):
1. Power Switch - This turns the main power on and off.
2. Fuse Holder - This holds a fuse that protects the internal power supply.
3. LED Display - This is a seven segments display that indicates DMX
signal, MIDI signal, DMX Function, Hold Function, DMX channel, and
is used to activate and make changes in the menu.
4. Up Button - This button is used to advance the selected readings in
the menu.
5. Down Button - This button is used to descend through the menu
selections.
6. Menu Button - Use this button to activate the system menu.
7. Chase Button - This button selects chase mode.
8. Store Button - Pressing this button stores a scene or recalls a stored
scene.
9. MIDI In - This connector is used to receive MIDI signal from a MIDI
controller or MIDI sequencer.
10. MIDI Thru - This connector is used to send the signal coming in from
the MIDI IN JACK (9) to another MIDI device.
11. DMX In - This 3-pin XLR jack is used to receive DMX signal from a DMX
controller.
12. DMX Out - This 3-pin XLR jack is used to send a DMX signal to a DMX
power pack or dimmer.
Multi-Data/Pak Instruction Manual Page 3
