background image

 

 

19 

 

User level  

NTH

 

low temperature set point for backup 
heating: 
The storage tank low temperature set-
ting that initiates backup heating refers 
to the storage tank selected by parame-
ter setting 

SNH

 = n  (n = 1 .. 3, level E3 

– 1 / 7).

 

 

It is the temperature that initiates dual-
source backup heating with reference 
to measurement TSPn (or TSRn if 
TSPn is not connected).  
Wird die minimale If the temperature 
falls below the low temperature setting 
during the time the backup heating 

SPA1

 

YES/NO – setting: 
Activate or temporarily deactivate stor-
age tank 1. 
 
 

No 3  

Deactivation occurs because the maxi-
mum storage tank heat transfer tempe-
rature is internally preset to 10°C. This 
setting is not affected by the collector 
safety function.

 

 

SPA1 = YES:  storage tank 1 activated 
SPA1 = NO:   storage tank 1 deacti-
vated 
default setting: SPA1 = YES 
 
 Parameter SPA1 is disabled for 
system configurations 1 and 8.

 

 

function is enabled, backup heating is 
activated until temperature TSPn (or 
TSRn) >= NTH + NHD, or until the ena-
ble time has elapsed.

 

NTH setting range: 10 .. 90°C;  
default setting: NTH = 40°C 
 
 The backup heating function is as-
signed to timer channel CH1. Backup 
heating enable times are programmed 
using CH1. If no times are set, backup 
heating is always enabled. 
(

NHD

 adjustable at level E3 – 2 / 7) 

SPA2

 

YES/NO – setting: 
Activate or temporarily deactivate stor-
age tank 2. 
 
 

No 4  

Deactivation occurs because the maxi-
mum storage tank heat transfer tempe-
rature is internally preset to 10°C. This 
setting is not affected by the collector 
safety function.

 

 

SPA2 = YES:  storage tank 2 activated 
SPA2 = NO: storage tank 2 deactivated 
default setting: SPA2 = YES 
 
 Parameter SPA2 is disabled for 
system configurations 1 and 8.

 

 

SPA3

 

YES/NO – setting: 
Activate or temporarily deactivate stor-
age tank 3. 
 
 

No 5  

Deactivation occurs because the maxi-
mum storage tank heat transfer tempe-
rature is internally preset to 10°C. This 
setting is not affected by the collector 
safety function.

 

 

SPA3 = YES:  storage tank 3 activated 
SPA3 = NO:  storage tank 3 deacti-
vated 
default setting: SPA3 = YES 
 
 Parameter SPA3 is disabled for 
system configurations 1,2,3,4,8,9 and 
11  

Summary of Contents for LOGON SOL plus

























Reviews: