background image

9

The pressurisation unit is supplied 
with a flying lead for the Mains Power 
Connection; this cable should not  
be replaced.
Mains connection must be via a 
fused isolator rated at 13 Amps and 
positioned locally to the unit. and 
within 1 metre of the unit. The cable 
size serving the unit shall be sized  
in accordance with the IEE  
Electrical Regulation.
After the outer casing has been 
removed, the Electrical Terminal 
Connection rail can be located  
on the front-hinged inner door.  
See Fig 9.1 for connection details.

9.1 Wiring details
The High & Low alarm switches have 
been wired to allow volt free indication 
of faults. If the power interruption of 
the associated Boiler/Chiller plant is 
required, the 230V 50Hz power supply 
for the associated Boiler / Chiller plant 
should be connected as follows:
Interlock circuit In 

Term 2

Link wire  

 

Terms 3 & 5

Interlock circuit Out 

Term 6

If a general alarm is required Link 
Terminal 6 to Terminal 8. Then the 
Interlock Circuit Out is Terminal 9.
In this manner, if one of the alarm 
switches are activated, the power 
supply to the associated Boiler /Chiller 
plant will be interrupted.

9.0 Electrical Connection

Electrical Connection

Figure 9.1 – wiring diagram

MAINS SUPPLY 

240V/50HZ 

10AMPS

GENERAL 

FAULT ALARM 

VOLT FREE 

(MAX 240V 0.5A)

HIGH 

PRESSURE 

ALARM VOLT 

FREE(MAX 240V 

0.5A)

LOW PRESSURE 

ALARM VOLT 

FREE (MAX 240V 

0.5A)

1

2

3

4

5

6

7

8

9

10

11

12

EAR

TH

N

EU
TR
AL

L

IVE

N

OR

M

AL
L

Y OPEN

NO

RMA

LLY

 CLO

S

E

D

CO

MMO

N

CO

MMO

N

LOW ALARM NO (PU POWERED)

LOW ALARM NC (PU POWERED)

LOW ALARM COMMON

HIGH ALARM NC (PU POWERED)

HIGH ALARM NO (PU POWERED)

HIGH ALARM COMMON

GENERAL ALARM NO (PU POWERED)

GENERAL ALARM NC (PU POWERED)

GENERAL ALARM COMMON

PUMP 1 LIVE

PUMP 1 NEUTRAL

MAINS NEUTRAL

MAINS LIVE

GREY

BLACK

BROWN

BROWN

BROWN

BLUE

BLUE

GR

EY

GR

EY

GR

EY

BR
OWN

BR
OWN

BR
OWN

BR
OWN

BL
AC
K

BL
AC
K

BL
AC
K

B

LUE

G/Y

YELLOW

BLUE

GREEN

RED

RED

YELLOW

BLUE

GREEN

PRESSURE TRANSPONDER CABLE

TANK LEVEL SWITCH

MAIN CONTROLLER PCB

USER TERMINAL

240/

50Hz

SENSOR 
CONNECTOR

BOX 
CONNECTOR

RED TERMINAL

YELLOW TERMINAL

BLUE TERMINAL

GREEN TERMINAL

1

4

Not Connected

2

3
4
5
6
7
8
9

10

11

12
13
14
15

1
2

WATER LEVEL SWITCH

BLACK

GREY

BROWN

GREY

BLACK

BROWN

PUMP

NO

RMA

LLY

 CLO

S

E

D

N

OR

M

AL
L

Y OPEN

NO

RMA

LLY

 CLO

S

E

D

CO

MMO

N

N

OR

M

AL
L

Y OPEN

DISPLAY PCB

Summary of Contents for Minifill-E



















Reviews: