Set the time switch to operating mode (ESC).
Press the CH button
repeatedly until the
correct channel is
displayed.
Press the UP, DOWN or
STOP button; the shutter
moves in the desired
direction or stops.
Set the time switch to operating mode (ESC).
Press MODE until the
dice appears on the
display.
In vacation mode, the holiday mode is
deactivated with a random offset of ±15
minutes.
Set the time switch to operating mode (ESC).
Switch the holiday
mode ON or OFF by
pressing the HOLI
button.
The weekday SU
blinks on the display.
If you have activated the holiday mode
prior to 18:00 hrs, it is automatically
deactivated at 24:00 hrs of the same
day.
If you have activated the
h
oliday
mode
after 18:00 hrs, it is first automatically
deactivated at 24:00 hrs on the next
day
.
.
In vacation mode, the holiday mode is
deactivated with a random difference of 15
minutes
CH
OK
CLOCK
PROG
ADJ
MODE
ESC
S/W DEL
HOLI
CH
OK
CLOCK
PROG
ADJ
MODE
ESC
S/W DEL
HOLI
CH
OK
CLOCK
PROG
ADJ
MODE
ESC
S/W DEL
HOLI
Disposal
Conformi
t
y
Customer
S
ervice
Technical Details
E
Exchanging the Battery
F
Troubleshooting
Dispose of used batteries in a recycling bin
for batteries or via the specialist trade.
Put the packaging material into the recycling
bins for cardboard, paper and plastics.
If, despite correct handling, faults or malfunctions occur
or if the product was damaged, please contact your
retailer or the manufacturer.
ELDAT GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen
Germany
Phone:
+ 49 (0) 33 75 / 90 37-310
Fax:
+ 49 (0) 33 75 / 90 37-90
Internet:
www.eldat.de
E-mail:
info@eldat.de
Dispose of the waste product via a collection
point for electronic scrap or via your specialist
dealer.
Waste electrical products and batteries should not
be disposed of with household waste!
Hereby, ELDAT GmbH declares that the radio
equipment type RTS07 is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity
is available at the following internet address:
www.eldat.de
Frequency:
Radiated power:
0.43 mW
Modulation:
FSK
Coding:
Easywave
:
1x 3 V-
, CR2032
:
-
13 µA
- for a long faulty radio re-
ception of the Light Sensor
510 µA
(max. 20 min)
-
14 mA
:
0°C bis 50°C
:
-
150 m
-
30 m
:
80 x 80 x 16 mm
:
50 g
868,30 MHz
Voltage supply
battery
Power consumption
Static current
approx.
approx.
Transmission current
approx.
Operating temperature
Range
with good free field conditions
approx.
in buildings
approx.
Dimensions
approx.
Weight
approx.
- Blinking
symbol: exchange the battery.
(see chapter E).
-
programmed
switching commands in Automatic Mode: check
whether the Time Switch is in "Automatic Mode" (see
chapter C5). Check the programmed switching times
(see chapter C4.1). If necessary, re-enter the radio
channels of the radio timer into the radio controls
(see chapter B2).
- Solar protection/twilight mode cannot be activated:
re-establish the connection between the light sensor
and the ttime switch (see the operating instructions
for the Light Sensor SL01).
- The radio control does not move the shutter into the
intermediate position: set the runtime again (see
chapter B3).
- After changing the sensor´s battery, the light sensor
reception is disrupted and the SUN/MOON icon
blinks: Wait approx. 35 minutes until reception is
restored automatically.
- If there is no visible display: check the batterie´s
polarity or exchange the battery
- If the control does not react to pressing buttons in
manual operation: re-enter the radio channels of the
Radio Time Switch into the radio controls (see
chapter B2).
If the radio control does not react to the
The battery capacity is shown in the display with the
symbol
. If the complete battery symbol blinks the
battery needs to be exchanged.
The clock has a power reserve of some
minutes. If the radio time switch is without
voltage supply for a longer period, only the time
has to be reset
. All other settings remain as they
were.
If the bar of the battery icon blinks and the contur
shows permanently on the display of the time switch,
the battery of the light sensor needs to be exchanged.
Also see the operating instructions of the Light Sensor
SL01.
UM80508B 1017 GB
Warranty
Within the statutory warranty period we undertake to
rectify free of charge by repair or replacement any
product defects arising from material or production
faults.
Any unauthorized tampering with, or modifications to,
the product shall render this warranty null and void.
Replace the time switch in the wall mount. The
latches have to snap into place
.
Exchange the battery.
Only use batteries of the
type CR2032.
Observe the correct
polarity
!
Press the radio
timeswitch together in
the center on the top
and the bottom and pull
it out of the wall mount
.
D1
Activating the
H
oliday
Mode
D
Additional
F
unctions
C6
Manual Mode
In manual mode you can only raise or lower the
shutters by pushing a button.
DOWN
STOP
UP
(raise)
(lower)
D4
ng
D
R
Deleti
all ata ( eset)
D2
Activating
D
aylight
S
avings
T
ime
CH
CLOCK
W
MO TU WE
FR
SA
TH
SU
AUTO
HOLI
S/W DEL
S
AUTO
MO TU WE
FR
SA
SO
TH
Set the time switch to operating mode (ESC).
Press the S/W button for
more than 3 seconds.
The display changes
from
W
to
S
and the clock is moved
forwards/backwards one hour.
HOLI
S/W DEL
D3
Activate Vacation Mode
CH
OK
CLOCK
PROG
ADJ
MODE
ESC
S/W DEL
HOLI
PROG
MODE
S
AUTO
MO TU WE
FR
SA
SO
TH
CH
OK
CLOCK
PROG
ADJ
MODE
ESC
S/W DEL
HOLI
MANU
W
MO
TU WE TH FR
SA
SO
Press ESC and the DEL button at the
same time for more than 3 seconds.
All saved data are
deleted and the
factory settings are
restored.
After a RESET the radio channels do not
have to be learned into the radio control
again.
PROG
ADJ
MODE
ESC
S/W DEL
HOLI
ESC HOLI
S/W DEL
MANU
W
MANU
W
MANU
W
MANU
W
MANU
W
MO TU WE
FR
SA
SO
TH
MO TU WE
FR
SA
SO
TH
MO TU WE
FR
SA
SO
TH
MO TU WE
FR
SA
SO
TH
MO TU WE
FR
SA
SO
TH
Scope of
Delivery
Radio Time Switch RTS07, battery CR2032,
-
ment frame, attachment set, operating instructions
attach
Please read these instructions carefully
before using the product
Also observe the operating instructions of the
devices to be controlled
The automatic control of systems or devices that
need to be supervised is not permitted.
Have faulty Radio Time Switches checked by the
manufacturer
!
Do not make any unauthorized modifications to the
device!
!
Safety
Advice
C5
Changing the
O
perating
M
ode
Automatic
M
ode
Set the time switch to operating mode (ESC).
By briefly pressing the MODE button, select
the operating mode AUTO (automatic
mode) or AUTOMANU (automatic mode
with partial manual operation).
MANU
W
MO TU WE
FR
SA
SO
TH
AUTO
CH
OK
CLOCK
PROG
ADJ
MODE
ESC
S/W DEL
HOLI
PROG
MODE
W
MO TU WE
FR
SA
SO
TH
AUTO
Solar
P
rotection/
T
wilight
M
ode
Set the time switch to operating mode (ESC).
By briefly pressing the SUN/MOON button,
activate/deactivate solar protection, twilight
or both modes.
W
AUTO
MO TU WE
FR
SA
SO
TH
W
AUTO
MO TU WE
FR
SA
SO
TH
W
AUTO
TH
W
AUTO
TH
CH
OK
CLOCK
PROG
ADJ
MODE
ESC
S/W DEL
HOLI
ADJ
4/4
G
I
General nformation
